TRAPS FOR FEATHERED GAME.
[Illustration: A]mong the following will be found the various net
and cage traps commonly used in the capture of winged game, besides
several other unique devices in the shape of box traps, etc., many
of which are original with the author of this work and appear in
the present volume for the first time in book form. Commonest among
bird-catching machines, is the well known invention of
THE SIEVE TRAP.
This device certainly possesses one great advantage:--_it is not
complicated_. Any one possessed of a sieve and a piece of string
can get up the trap at two minutes' notice, and provided he has
patience, and can wait for his little bird, he is almost sure to
be rewarded for his pains,--if he wait long enough. This of course
depends upon circumstances: when the birds are plenty and are not
shy, it is a common thing to secure three or four at once in a
very few minutes, while at other times an hour's patient waiting
is unrewarded.
The trap consists only of a sieve tilted up on edge and thus propped
in position by a slender stick. To this stick a string or thread is
attached and the same carried to some near place of concealment,
when the trapper may retire out of sight and watch for his "little
bird." The ground beneath the sieve is strewn with bread crumbs,
seed or other bait, and while the unsuspecting birds are enjoying
their repast, the string is pulled and they are made prisoners.
The sieve may be arranged with a spindle as described for the coop
trap, page (68), and may thus be left to take care of itself. Where
[Page 66]
the birds are plenty and easily captured, the former method answers
the purpose perfectly, but when tedious waiting is likely to ensue
the self-acting trap is better.
THE BRICK TRAP.
This is a very old invention, and has always been one of the three
or four stereotyped specimens of traps selected for publication in
all Boys' Books. It is probably well known to most of our readers.
Take four bricks, and arrange them on the ground, as seen in our
engraving, letting them rest on their _narrow_ sides. If properly
arranged, they should have a space between them, nearly as large
as the broad surface of the brick. A small, forked twig of the
shape shown in the separate drawing (_b_) having a small piece
cut away from each side of the end, should then be procured. Next
cut a slender stick, about four inches in length, bluntly pointed
at each end. A small plug with a flat top should now be driven
into the ground, inside the trap, about three inches from either
of the end bricks and projecting about two inches from the ground.
The trap is then ready to be set. Lay the flat end of the forked
twig over the top of the plug, with the forks pointing forward,
or toward the end of the enclosure nearest the plug. The pointed
stick should then be adjusted, placing one end on the flat end of
the fork, over the plug, and the other beneath the fifth brick,
which should be rested upon it. The drawing (_b_) clearly shows
the arrangement of the pieces. The bait, consisting of berries,
bird-seed, or other similar substances should then be scattered
on the ground on the inside of the enclosure. When the bird flies
[Page 67]
to the trap he will generally alight on the forked twig, which by
his weight tilts to one side and dislodges the pieces, thus letting
fall the sustained brick.
[Illustration]
It is not intended to kill the bird, and when rightly constructed
will capture it alive. Care is necessary in setting the topmost
brick in such a position that it will fall aright, and completely
cover the open space. This is a very simple and effectual little
contrivance, and can be made with a _box_ instead of bricks, if
desired. A piece of board may also be substituted for the top brick,
and the enclosure beneath made larger by spreading the bricks further
apart, thus making a more roomy dungeon for the captive bird.
[Illustration]
THE COOP TRAP.
This is another excellent device for the capture of birds and large
feathered game, and is used to a considerable extent by trappers
throughout the country. Like the brick trap, it secures its victims
without harm and furnishes the additional advantage of good ventilation
for the encaged unfortunate. Any ordinary coop may be used in the
construction of this trap, although the homely one we illustrate
is most commonly employed on account of its simplicity and easy
manufacture. It also does away with the troublesome necessity of
carrying a coop to the trapping ground, as it can be made in a
very few minutes with common rough hewn twigs by the clever use
of the jack knife. The only remaining requisites consist of a few
yards of very stout Indian twine, several small squares of brown
pasteboard, a dozen tacks and a number of pieces of board five
inches square, each one having a hole through its centre, as our
engraving (_b_) indicates. Having these, the young trapper starts
out with material sufficient for several coops, and if he is smart
[Page 68]
will find no difficulty in making and setting a dozen traps in a
forenoon.
[Illustration]
In constructing the coop, the first thing to be done is to cut
four stout twigs about an inch in thickness and fifteen inches
in length and tie them together at the corners, letting the knot
come on the inside as our illustration (_a_) explains and leaving
a loose length of about two feet of string from each corner. This
forms the base of the coop. Next collect from a number of twigs of
about the same thickness, and from them select two more corresponding
in length to the bottom pieces. Having placed the base of the coop
on the ground, and collected the strings inside proceed to lay
the two selected sticks across the ends of the
[Page 69]
uppermost two of the square, and directly above the lower two.
Another pair of twigs exactly similar in size should then be cut
and laid across the ends of the last two, and directly above the
second set of the bottom portion, thus forming two squares of equal
size, one directly over the other. The next pair of sticks should
be a trifle shorter than the previous ones and should be placed a
little inside the square. Let the next two be of the same size as
the last and also rest a little inside of those beneath them, thus
forming the commencement of the conical shape which our engraving
presents. By thus continuing alternate layers of the two sticks
cob-house fashion, each layer being closer than the one previous,
the pyramid will be easily and quickly formed. After ten or a dozen
sets have been laid in place, the arm should be introduced into
the opening at the top, and the four cords drawn out, letting each
one lay along its inside corner of the pyramid. Taking the strings
loosely in the left hand and having the twigs in readiness, proceed
to build up the sides until the opening at the top is reduced to
only four or five inches across. The square board will now come
into play. Pass the ends of the cords through the hole in its centre
and rest the edge of the board on the top pair of sticks, taking
care that it is the tip of the grain of the wood instead of its
side, as otherwise it would be likely to crack from the pressure
that is about to be brought upon it. Have ready a stout peg of
hard wood, and laying it over the hole in the board, and between
the strings, proceed to tie the latter as tightly as possible over
it. By now turning the peg, the cords will be twisted and tightened
and the various pieces of the coops will be drawn together with
great firmness, in which state they may be secured by the aid of
a tack driven in the top board against the end of the peg as shown
at (_b_). Thus we have a neat and serviceable coop, which will
last for many seasons. To _set_ the affair it is necessary to cut
three sticks of the shapes shown in our illustration. The prop
piece is a slender forked twig about ten inches in length from
the tip to the base of the crotch. The spindle is another hooked
twig of the same length: the bait piece is quite similar to the
latter, only an inch shorter and supplied with a square notch at
the tip. It is also slightly whittled off on the upper side to
receive the square of pasteboard or tin, which is to hold the bait
and which may be easily fastened in place by a tack. All of these
twigs may be easily found in any thicket by a little practice in
searching. In setting the trap, it is only necessary to raise up
one side of the coop to the height of the prop stick, insert the
[Page 70]
short arm of the spindle through the fork and beneath the edge of
the coop. While holding it thus in position, hook the crotch of the
bait stick around the lower piece at the back of the coop, and
pushing the end of the spindle inside the coop, catch it in the notch
of the bait stick where it will hold, and the trap is ready to be
baited. The bait may consist of oats, wheat, "nannie berries" or the
like, and should be strewn both on the platform and over the ground
directly _beneath_ and around it. If properly set, a mere peck at the
corn will be sufficient to dislodge the pieces and the coop will fall
over its captive. It is not an uncommon thing to find two or even
three quail encaged in a trap of this kind at one fall, and after
the first momentary fright is over, they seem to resign themselves
to their fate and take to their confinement as naturally as if
they had been brought up to it.
The method of setting the coop trap above described is a great
improvement on the old style of setting, and is an improvement
original with the author of this work. In the old method a semi-circular
hoop of rattan is used in place of the bait stick above. The ends
of the rattan are fastened to one of the lower back pieces of the
coop, and the hoop is just large enough to fit inside the opening of
the coop. This rattan rests just above the ground, and the spindle
catches against its inside edge in place of the notch in the bait
stick already described, the bait being scattered inside the hoop.
When the bird approaches, it steps upon the rattan, and thus pressing
it downward releases the spindle and the coop falls; but experience
has shown the author that it does not always secure its intruders,
but as often falls upon their backs and sends them off limping
to regain their lost senses. By the author's improvement it will
be seen that the whole body of the bird _must_ be _beneath_ the
coop before the bait sticks can be reached and that when properly
set it is absolutely certain to secure its victim. The author can
recommend it as infallible, and he feels certain that anyone giving
both methods a fair trial will discard the old method as worthless
in comparison.
THE BAT FOWLING NET.
With English bird-catchers this contrivance is in common use, but
so far as we know it has not been utilized to any great extent in
this country. It is chiefly used at night by the aid of a lantern,
and large numbers of sparrows and other birds are often secured.
[Page 71]
[Illustration]
Our illustration gives a very clear idea of the net, which may be
constructed as follows: Procure two light flexible poles, about
eight feet in length; to the tip of each a cord should be attached,
and the same secured to the middle of the pole, having drawn down
the tip to the bend, shown in our engraving. The two bent ends
should now be attached together by a hinge of leather. A piece
of mosquito netting is next in order, and it should be of such
a size as to cover the upper bent halves of the poles, as seen
in the illustration--the bottom edge being turned up into a bag,
about ten inches in depth. The contrivance is now complete, and is
used as follows: Three persons are generally required, and a dark
night is chosen. Hay stacks, evergreens, and thick bushes offer a
favorite shelter to numerous small birds, and it is here that they
are sought by the bird-hunters. A breezy night is preferable, as
the birds perch low, and are not so easily startled by unusual
sounds.
Great caution, however, is used in the approach. One party holds
the light, which is generally a _dark_ lantern, another takes the
net, and the third arms himself with a switch with which to beat
the bushes. The net is first held upright about a foot from the
bush, and the light thrown upon the back of it. The bush is then
moderately beaten, and the birds affrighted and bewildered fly against
the net, which is instantly closed. The bird is thus captured, and
when a full roost can be discovered a large number may be taken
in a single night. The lantern should be closed while not in actual
use, and everything should be done as quietly as possible. The
dark lantern in itself is useful without the net. The light often
so bewilders the bird that it flies directly in the face of the
lantern and flutters to the ground, where it may be easily taken
with the hand.
[Page 72]
THE CLAP NET.
In Asia, Africa, South America and Europe, this trap is a common
resource for the capture of wild birds of various kinds. It may be
called a "decoy" trap, from the fact that "call birds" are generally
used in connection with it. They are placed at distances around the
trap, and attract the wild birds to the spot by their cries. These
birds are especially trained for the purpose, but almost any tamed
bird that chirps will attract its mates from the near neighborhood,
and answer the purpose very well. Sometimes the "decoys" are entirely
dispensed with, and the "bird whistle" used in their stead. This
will be described hereafter, and inasmuch as the training of a
"decoy" would be a rather difficult matter, we rather recommend
the use of the bird whistle. The skill and absolute perfection of
mimicry which is often attained by bird fanciers with the use
of this little whistle, is something surprising.
[Illustration]
No matter what the species of bird--whether crow, bobolink, thrush
or sparrow, the song or call is so exactly imitated as to deceive
the most experienced naturalist, and even various birds themselves.
Of course this requires practice, but even a tyro may soon learn
to use the whistle to good advantage.
The clap net commonly used, is a large contrivance--so large that
several hundred pigeons are often caught at once. It is "sprung"
by the bird-hunter, who lies in ambush watching for the game. The
net is generally constructed as follows, and may be made smaller
if desired:--
[Page 73]
Procure two pieces of strong thread netting, each about fifteen
feet in length, and five feet in width. Four wooden rods one inch
in thickness and five feet in length are next required. These may
be constructed of pine, ash, or any other light wood, and one should
be securely whipped to each end of the netting.
Now by the aid of a gimlet or a red-hot iron, the size of a slate
pencil, bore a hole through one end of every piece one inch from
the tip, taking care that the ends selected lay on the same side of
the net. The other extremities of the four poles should be supplied,
each with a large screw eye. Four pegs are next in order--one of
which is shown separate at (_P_). It should be about eight inches
in length, and three inches in width, and an inch in thickness, and
sharpened to a point at one end. The other end should be supplied
with a notch two inches in depth and of such a width as will easily
secure the perforated end of one of the poles already described.
By the use of the gimlet or a red-hot nail, a hole should now be
bored through the side of every peg across the centre of the notch
for the reception of a wire pin or smooth nail.
The nets may now be rolled up on the poles, and the trapper may
thus easily carry them to his selected trapping ground. This should
be smooth and free from stones and irregularities. Unroll the nets
and spread them flatly on the ground, as seen in the illustration.
Let the perforated ends of the poles be innermost, and allow a
space of six feet between the inner edges of the nets. Draw the
net flatly on the ground, and drive one of the notched pegs at
each of the inside corners, securing the poles into the slots by
the aid of the wire pins or nails. Next cut four stakes eight or
ten inches long. The places for these may be seen by a look at
our engraving. Each one should be inserted _five feet_ distant
from the notched peg, and _exactly_ on a line with the _inside_
edge of the net--one for each corner. They should slant from the
net in every case. To each one of these stakes a stay-rope should
be secured, and the other end passed through the screw eye of the
nearest pole, drawing the string tightly, so as to stretch the net
perfectly square. Next, take a piece of cord, about twenty feet
in length, and fasten it across the ends of the net into the screw
eyes in the poles. This is the loop to which the draw-string is
attached, and either end of the net may be chosen for this purpose.
To this loop and a _little one side of the middle_, the draw-string
should be fastened. If secured exactly in the middle of the loop,
the two nets will _strike_ when the draw-rope is pulled, whereas
[Page 74]
when adjusted a little to one side, the nearest net will move a
trifle faster than the other, and they will overlap neatly and without
striking--completely covering the ground between them. When the
trap is spread the draw-rope should extend to some near shelter
where the bird-catcher may secrete himself from view. Spreading the
bait on the ground between the nets, and arranging his call birds
at the proper distances, he awaits his opportunity of springing
his nets. At the proper minute, when the ground is dotted with his
game, he pulls the draw-string, and the birds are secured.
Immense numbers of wild fowl are often captured in this way.
The "bird whistle," already alluded to, is often used with good
effect, it being only sufficient to attract the birds to such a
proximity to the net as will enable them to spy the bait, after
which their capture is easily effected.
THE BIRD WHISTLE.
This instrument, also known as the prairie whistle, is clearly
shown in our illustration. It is constructed as follows: First,
procure a piece of morocco or thin leather. From it cut a circular
piece one inch and a quarter in diameter. Through the centre of
this disc, cut a round hole, one-third of an inch in diameter. A
semi-circular piece of tin is next required. It should be of the
shape of an arc, as seen in our illustration; its width across
the ends being about three-quarters of an inch, and its entire
length being pierced with a row of fine holes. Next procure a piece
of thin sheet India rubber or gold beater's skin. Cut a strip about
an inch in length by half an inch in width, and lay one of its long
edges directly across the opening in the leather disc. Fold the
leather in half (over the rubber), and draw the latter tightly. Next
lay on the arc of tin in the position shown in the illustration, and
by the aid of a fine needle and thread sew it through the holes,
including both leather and rubber in the stitches. When this is
done, the whistle is complete. If the gold beater's skin is not
attainable, a good substitute may be found in the thin outer membrane
of the leaf of a tough onion or leak, the pulp being scraped away.
[Illustration]
[Page 75]
To use the whistle, place it against the roof of the mouth, tin
side up, and with the edge of the rubber towards the front. When
once wet, it will adhere to the roof of the mouth, and by skilful
blowing, it can be made to send forth a most surprising variety
of sounds. The quack of the duck and the song of the thrush may
be made to follow each other in a single breath, and the squeal
of a pig or the neigh of a horse are equally within its scope. In
short, there is scarcely any animal, whether bird or quadruped,
the cry of which may not be easily imitated by a skilful use of
the prairie whistle, or, indeed, as it might with propriety be
called, the "menagerie whistle."
THE WILD GOOSE TRAP.
In our northern cold regions, where the wild geese and ptarmigan
flock in immense numbers, this trap is commonly utilized. It consists
merely of a large net fifty feet in length, and fifteen in width,
arranged on a framework, and propped in a slanting position by
two poles, after the manner of the sieve trap. It is generally
set on the ice; and the trapper, after attaching his strings to
the props, and sprinkling his bait at the foot of the net, retires
to a distance to await his chances. Tame geese are often used as
decoys, and sometimes the bird whistle already described is used
for the same purpose. For the capture of the ptarmigan, the bait
consists of a heap of gravel. It is hard to imagine a less tempting
allurement, but as the food of the birds during the winter is sapless
and hard, it becomes necessary for them to swallow a considerable
amount of gravel to promote digestion. The great depth of the snow
renders this commodity very scarce during the winter season; and
the Indians, taking advantage of this fact, succeed in capturing
immense numbers of the game in nets by the use of that simple
allurement. The gravel is packed on the surface of a pile of snow,
placed under the centre of the net, and the draw-string is carried
to some neighboring shrubbery or place of concealment, where the
trapper can always get at it without being seen by the birds under
the net.
When everything is thus prepared, the hunters start out into the
adjacent woods and willows, and drive their game toward the nets.
This is generally an easy matter, and, no sooner do the birds come
in sight of the heap of gravel, than they fly towards it _en masse_,
and the ground beneath the net is soon covered with the hungry game.
[Page 76]
The hunter then goes to the end of the line, and, with a sudden pull,
hauls down the stakes: the net fans over the birds, and they are
prisoners.
Hundreds of ptarmigan are often thus caught by a single sweep of
the net. The trap is simply arranged, and may be constructed on
a reduced scale for smaller birds, if desired.
THE TRAP CAGE.
[Illustration]
Among bird-catchers generally, this is the favorite and most universal
trap; and, where a _decoy_ bird is used, it is particularly successful.
The cage is arranged in two compartments,
[Page 77]
one above the other,--the lower one being occupied by the call-birds.
The making of the cage requires considerable ingenuity and much
patience; and, for the benefit of those who may desire to exercise
that patient ingenuity, we will subjoin a few hints, which may
help them along in their efforts. For an ordinary cage, the height
should be about one foot, the broad sides the same, and the top
and other two sides eight inches. First cut four corner uprights.
These should be three-quarters of an inch square, and one foot in
length. Next cut a bottom board of pine, twelve inches by eight
inches, and one inch in thickness. From each of its corners, cut a
small cube of the wood, exactly three-quarters of an inch square,
thus leaving four notches, which will exactly receive the ends of
the uprights, as seen at (_a_). Before adjusting these pieces,
the four sides of the boards should be pierced with small holes,
as is also shown in the diagram (_a_). These may be punched with a
brad-awl, and should be about half an inch apart, and three-eighths
of an inch from the edge of the board. Each one of the uprights
may then be secured in place by two long brads, one being hammered
each way into each side of the notch. Next proceed to cut four more
of the square sticks. Two of these should be one foot in length,
and the remaining two eight inches. The corners of these should
now be neatly bevelled off, so as to fit after the manner of a
picture-frame. They should then be attached to
[Page 78]
the upper ends of the uprights by a brad through the corner of
each, as seen at (_b_), the dotted lines indicating the end of
the upright beneath. These sticks should likewise be pierced with
holes to correspond with those in the bottom board, and running
up and down in the direction of the wires.
[Illustration]
The middle tier of braces are next required. Two of these should be
ten and a half inches in length, and the other two six and a-half,
and the ends should be perfectly smooth. These should now be punched
with holes corresponding with those above, after which they may
be inserted between the uprights as seen in the engraving, and
secured by a brad at each end.
The trap door is shown separate at (_c_). The side sticks should
be eight inches in length, and one-half an inch square, and the
top and bottom sticks five inches in length. They should be set
in _between_ the side sticks, and the lower one should be secured
about half an inch above the lower ends of the uprights, as seen
in the illustration. The holes should be made in the side pieces,
and the wire run across from side to side, as shown. Annealed iron,
or copper wire is best for this purpose. The door should now be
pivoted or hinged at the top of the cage, between the long sides,
in such a position as that the top end shall rest on one of the
narrow upper edges of the cage. A stiff wire should be used for
the hinge, being passed through the top pieces of the cage into the
lower ends of the door pieces. The cage may now be wired throughout.
This is an easy matter, if the holes are properly made. About thirty
yards of the wire will be required: iron wire is generally used.
It should be about the size of a hair-pin, and should work easily.
Commence by passing it from the under side of the bottom board
through one of the holes next to the corner. Pass the wire upward,
through the centre braces, again upward through the top piece and
across to the opposite broad side and corresponding hole. From
this point it should pass downwards, through centre brace, and
again through the bottom. Draw the wire tightly and passing it
upward through the hole next to it, bring it over the top of the
cage and around again to the bottom edge from which it started.
Continue thus until the hinge of the door is reached; after which
the wire should be passed up and down on the same side and thus
carried around the small end of the cage until it finally meets
at the door hinge on the opposite side. The two halves of the cage
should now be separated by a grating of wire, as seen in the main
[Page 79]
illustration. This may be accomplished either by passing the wire
from side to side, around the base of each upright wire, or an
additional horizontal row of holes below the others may be punched
for the purpose. The door through which the call-bird is introduced
should next be made in the bottom section. There are two ways of
doing this: one method consists in sawing a hole three inches square
in the bottom board of the cage; and a cover consisting of a piece
of tin is made to slide beneath the heads of four tacks, two of which
are placed on each side of the opening. This form of door is perhaps
the simplest of the two. The other is shown separate at (_f_),
together with its mode of attachment.
It consists of two side pieces of wood, about a third of an inch
square, and three inches in length, and two shorter ones, two inches
in length. These are arranged into a square framework by a board
in each corner. Four holes are to be pierced in each side piece,
at equal distances. Commencing at the top, the door should then
be wired as directed for the cage. The lowest hole on each side
should be left open for a separate piece of wire. The cage should
now receive attention. The broad side is generally selected for
the door. Find the seven centre wires and connect them across the
middle by another horizontal bit of wire. This may be easily done
with a pair of pincers, by compressing a loop at each end of the
wire around the two which run perpendicularly at its ends. When this
is performed the five intermediate wires should be cut off about
a quarter of an inch below the horizontal wire, and the projecting
tips looped back over the cross piece, and made fast by the pincers.
The lower parts of the upright wires may now be cut off close to the
board. We will now take up the door. Pass a piece of wire through
the holes at the bottom, clap the door over the opening, and loop
the ends of the projecting wire loosely around the upright wires
at each side. This will allow the door to slide easily up and down.
Another wire should now be interlaced downwards through the centre
of the door, and bent into a ring at the top. Let the door rest
on the bottom of the cage, and, while in this position, adjust
the ring at the top around the central wire directly behind it.
The door is then complete, and, if properly made, will look neat
and work easily.
The "trap" at the top of the cage is next in order. To complete
this it is first necessary to interweave a _stiff_ wire loop, as
seen at (_d_). The loop should extend on the _inside_ of the lower
piece of the door and about two inches below it. The
[Page 80]
_spring_ power consists of a piece of stiff hoop-skirt wire, interwoven
between the wires of the top of the cage, and those of the door,
while the latter is shut. The force of this will be sufficient
to bring down the door with a snap; and for further security a
catch, such as is described in page (88), may be added if desired.
The spindle is next required. This is shown at (_g_), and consists
of a small perch of wood seven inches in length, and notched at
each end. In setting the trap, the door should be raised as seen
in the main illustration. One of the notches in the spindle should
now be caught beneath the loop and the other around one of the
central wires in the end of the cage. The bait, consisting of a
berry, bird-seed, or what-not, may be either fastened to the spindle
or placed beneath on the wires. The call-bird having been introduced,
the trap may now be left to itself. If the call-bird is well trained
it will not be many minutes before the birds of the neighborhood will
be attracted to the spot by its cries. Ere long one less cautious
than the rest will be seen to perch upon the top of the cage. He
soon discovers the bait, and alighting upon the perch, throws it
asunder, and in an instant the trap door closes over its captive.
The cage is sometimes constructed double, having two compartments
beneath for call-birds, and two traps above, in general resembling
two of the single traps placed side by side. The decoy bird is not
an absolute necessity to the success of the trap. Many birds are
caught simply by the bait alone. The trap cage, when constructed
on a larger scale, is often successfully employed in the capture
of the owl. In this case it is baited with a live mouse or bird,
and set during the evening in a conspicuous place. A trap working
on this principle, being especially adapted to the capture of the
owl, will be noticed hereafter.
THE SPRING NET TRAP.
Although slightly complicated in construction, our next illustration
presents one of the prettiest bird traps on record, and may be
made in the following manner, and by frequently referring to the
picture, our explanation will be easily understood.
The first step is to make or procure a low flat box, about fifteen
inches long, by ten inches in width, with a depth of about two
inches. Next fasten an interior box, of the same
[Page 81]
height, leaving a space of about three-quarters of an inch between
them all round. A platform should now be made. Let it be of such a
size that it will just fit in the interior box, with a very slight
space all around its edge. It should then be pivoted in the upper
part of this box by two small slender pins, one being driven through
into its edge, at the centre of each end. Let it be sensitively
poised. The next thing to be done, is to arrange the spindle and
catch. The latter should consist of a tack or small bit of wood
fastened on the middle of the platform, about an inch from one
end, as seen both in the main illustration and in the diagram at
(_b_).
[Illustration]
The spindle should consist of a flat piece of wood, secured with
a leather hinge to the edge of the outside box, directly opposite
the catch. Let it be long enough to reach and barely hold itself
beneath the catch. When thus in its position, two small plugs should
next be driven into the edge of the inner box, one on each side of
the spindle, thus holding it in place. A glance at our illustration
makes this clear. The netting and "hoop" are next in order. The hoop
should consist of an iron wire of the diameter of common telegraph
wire.
For a box of the size we have given, a length of about twenty-eight
inches will be found to answer. Before making the hoop, however,
its hinges should be ready for it. Two screw eyes, or staples of
bent wire should be driven into the bottom of the box between the
two walls, one in the exact middle of each side. The iron wire
should now be bent so as to fit round and settle into the space
between the boxes, letting each end rest
[Page 82]
over the screws in the bottom. It will be found that there will
be enough surplus wire on each end to form into a loop with the
pincers. These loops should be passed through the screws or rings
already inserted, and then pinched together; the hinge will thus
be made, and will appear as at (_c_). If properly done, they should
allow the hoop to pass freely from one end of the box to the other,
and settle easily between the partitions. If this hinge should
prove too complicated for our young readers, they may resort to
another method, which, although not so durable, will answer very
well. In this case the wire will only need to reach to the exact
middle of the long sides. No surplus being necessary, a length
of twenty-six inches will be exactly right. On each end a short
loop of tough Indian twine should be tied. By now fastening these
loops to the bottom of the box with tacks, in the place of screws,
it will form a hinge which will answer the purpose of the more
complicated one.
[Illustration]
The netting should consist of common mosquito gauze, or, if this
cannot be had, any thin cloth may be substituted. It should be
sewed fast to the iron wire, from hinge to hinge, and then, with
the hoops resting in its groove, the netting should be drawn over the
platform, and tacked to the bottom of the groove, on its remaining
half. It should rest loosely over the platform to allow plenty of
space for the bird.
But one more addition, and the trap is finished. We have mentioned
the use of elastics in other varieties: they are of equal use here,
and should be attached to the hoop as seen at (_a_) in the section
drawing, the remaining ends being fastened to the bottom of the
groove, as there indicated. These elastics should be placed on
both sides, and stretched to such a tension as will draw the hoop
quickly from one side to the other.
It will now be easy to set the trap. Draw the hoop back to the
opposite end, tucking the netting into the groove; lower the spindle
over it, resting it between the two little plugs, and securing
its end beneath the catch on the platform. If the bait,
[Page 83]
consisting of bread-crumbs, berries, insects, or the like, be now
sprinkled on the platform, the trap is ready for its feathered
victim. It will easily be seen that the slightest weight on _either_
side of this poised platform will throw the catch from the end of
the spindle, and release the hoop and the platform in an instant
is covered by the net, capturing whatever unlucky little bird may
have chanced to jump upon it. This is a very pretty little trap,
and will well repay the trouble of making it.
A SIMPLER NET TRAP.
[Illustration]
Much ingenuity has been displayed in the construction of bird traps
of various kinds, but often the ingenuity has been misplaced, and
the result has been so complicated as to mar its usefulness for
practical purposes. The examples of net traps presented in this
volume are so simple that the merest tyro can readily understand
them. What can be more so than the present example, and yet it
is as sure in its effect, and _surer_ than those other varieties
of more complicated construction. One necessary element in a trap
of any kind is, that the bearings are slight and that they spring
easily. To obtain this requisite it is necessary to overcome friction
as much as possible, using only a small number of pieces, and having
as few joints and hinges only as are absolutely necessary. The present
variety possesses advantages on this account. It is constructed
somewhat on the principle of the ordinary steel trap, and also
resembles in other respects the one we have just described, although
much simpler. We give only a section drawing, as this will be
sufficient. The long side of a flat board of about eight by sixteen
inches is shown at (_a_); (_b_) indicates the loops of a bent wire,
to which the netting is attached, as in the trap just described,
[Page 84]
the loops being fastened to the board as in the other variety;
(_g_) consists of a small bit of wood an inch or so in length and
half an inch in width. It should be tacked on to the middle of
the one end of the board and project about a half inch above the
surface. To the top of this the spindle (_c_) should be attached
by a leather or staple hinge. The spindle should be of light pine,
five inches in length and a quarter of an inch square, bevelled;
on the under side of one end (_d_) is the catch or bait piece,
and should be whittled out of a shingle or pine stick of the shape
shown, the width being about a half an inch or less. One side should
be supplied with a slight notch for the reception of the spindle,
and the other should project out two or three inches, being covered
on the top with a little platform of pasteboard, tin, or thin wood
either glued or tacked in place. To attach this piece to the main
board, two small wire staples may be used, one being inserted into
the bottom end of the piece and the other being hooked through
it, and afterward tacked to the bottom of the trap, thus forming
a loop hinge. Another method is to make a hole through the lower
tip of the bait piece by the aid of a red-hot wire, as seen at
(_d_), afterwards inserting a pin and overlapping its ends with
two staples driven into the bottom board, as shown at (_e_). In
our last mentioned net trap the spring power consisted of rubber
elastic, and the same may be used in this case, if desired, but by
way of variety we here introduce another form of spring which may
be successfully employed in the construction of traps of various
kinds. It is shown at (_o_) and consists merely of a piece of tempered
hoop iron, so bent as to act with an upward pressure. It should be
about three inches long by half an inch wide. About three-quarters
of an inch should be allowed for the two screws by which it is to
be attached to the board. The rest should be bent upward and thus
tempered by first heating almost to redness, and then cooling in
cold water.
One of these springs should be fastened to the board on each side,
directly under the wire and quite near the hinge, in the position
shown in the main drawing. Now draw back the net, lower the spindle
and catch its extremity in the notch of the bait piece, and the trap
is set as in our illustration. Sprinkle the bait on the platform,
and lay the machine on the ground where birds are known to frequent;
and it is only a matter of a few hours or perhaps minutes, before it
will prove its efficacy. In order to prevent the bird from raising
the wire and thereby escaping, it is well to fasten a little tin
[Page 85]
catch (_f_) at the end of the board. This will spring over the wire
and hold it in its place.
THE UPRIGHT NET TRAP.
The following is another novelty in the way of a bird-trap, somewhat
similar to the one we have just described, in its manner of working.
Procure two pieces of board about a foot square. Nail one to the
edge of the other, as represented in our engraving. A stout wire
is the next requisite. It should be about thirty inches long, and
bent either into a curve or into two corners, making three equal
sides. Each end of the wire should then be bent into a very small
loop for the hinge. On to this wire the netting should then be
secured as in the two previous examples, after which the ends of
the wire may be tied with string or hinged on wire staples into
the angle of the two boards, as seen in our illustration. Allow
the wire now to lie flat on the bottom board, and then proceed
to tack the netting around the edges of the upright board. Two
elastics should next be fastened to the wire on each side, securing
their loose ends to the bottom of the trap. They should be tightly
drawn so as to bring the wire down with a snap. The spindle of
this trap should be about eight or nine inches long, square and
slender,--the lower end being flattened, and the upper end secured
to the top edge of the upright board by a hinge of leather or string.
An excellent hinge may be made with a piece of leather an inch
and a half long, by half an inch in width, one half of the length
being tied around the end of the spindle, and the other tacked
on to the upper edge of the board.
The platform is given by itself at (_a_) in the same picture. It
may be made of very thin wood--cigar box wood, for instance, or
even thick pasteboard. It consists of three pieces. The piece which
is hinged into the angle of the boards should be about three inches
in length; the platform piece ought not to be more than four inches
square, and the upright piece only long enough to reach the tip of
the spindle when the platform is raised, as shown in our engraving.
The hinge piece should be cut to an edge on that end where the
leather is fastened, the opposite end being bevelled off in order
that the platform may rest and be tacked or glued firmly upon it.
The diagram (_a_) will make this all very clear.
When the platform is all made and fastened in its place, the
[Page 86]
trap may be set. Draw the hoop back as far as possible, and lower
the spindle over its edge, catching it behind the upright stick on
the platform. If the trap is properly constructed, the pressure
of the spindle on the platform will suffice to hold it up as seen
in our illustration. The upright stick on the back of the platform
should never be more than an inch and a half from the back of the
trap. If need be, a slight notch may be made in the end of the
spindle and a small tack driven into the back of the upright stick
to correspond to it. By thus fitting the notch under the head of the
tack, it will be sure to hold the platform in the right position.
But it should be carefully tested before setting, to see that it
springs easily.
[Illustration]
When thus set sprinkle the bait on the platform, scattering a little
also on the bottom of the trap and on the ground directly around it.
The little birds will soon spy the tempting morsels, and alighting
on the trap are misled, and the slightest peck or pressure on the
platform where the bait is most bounteously spread brings down the
wire and net with a _snap_, and the little creature is secured
without harm.
[Illustration: Method 2.]
Our next illustration shows another method of constructing the platform.
It should be about three or four inches square,
[Page 87]
and on the middle of one of its edges the upright catch piece should
be fastened. This piece, as will be seen in our engraving, should
be cut spreading at the bottom so as to admit of being secured to
the platform by two brads, the tip being cut to a point. The total
length of this piece should not be over two and a half inches. When
tacked in place, a third brad should be inserted between the other
two and exactly in the centre of the side of the platform. This
latter brad is to act as the pivot, or hinge, and should project
about a quarter of an inch, as seen at (_a_). On the opposite edge
of the platform another larger brad should be driven, having its
end filed to a blunt point, as in (_b_). If the filing would be
too tedious, a plug of hard wood of the required shape would answer
every purpose. The upright props which support the platform should
be cut of thin wood. Let one be an inch and a half long and half
an inch wide, the other being an inch in length. Each should have
one end whittled to a point, which will admit of its being inserted
in a gimlet hole in the bottom of the trap. These gimlet holes
should be made at least half an inch in depth. Make the first at
about an inch or so from the back of the trap. Into this insert
the shorter pieces, broadside front. Lay the pivot brad of the
platform on the top of this piece and insert over it a small wire
staple, as seen at (_a_). Elevate the platform evenly and determine
the spot for the other gimlet hole, which should be directly beneath
the point of the filed brad. Be sure that it is in the middle of
the board, so that the platform may set squarely, and be perfectly
parallel with the sides. Insert the remaining prop in its place,
and the platform is complete. The overhanging spindle now requires a
little attention. This should be whittled off on each side, bringing
it to a point at the tip. On each side of the spindle a long plug
should then be driven into the back piece, as our illustration
shows. These should be far enough apart to allow the spindle to
pass easily between them. The _setting_ of the trap is plainly shown
[Page 88]
in our engraving. The spindle being lowered between the plugs is caught
finely on the tip of the catch-piece. The blunt point at the opposite
end of the platform should have a slight hollow made for it in the
prop against which it presses. If the platform be now strewn with
bait, the little machine is ready. It is certainly very simple and
will be found very effective.
THE BOX OWL TRAP.
The use of a box trap for the capture of an owl is certainly an
odd idea, but we nevertheless illustrate a contrivance which has
been successfully used for that purpose.
The box in this case should be of the proportions shown in our
engraving, and well ventilated with holes, as indicated. (This
ventilation is, by-the-way, a good feature to introduce in _all_
traps.) Having made or selected a suitable box--say, fourteen or
more inches wide, provided with a cover, working on a hinge--proceed
to fasten on the outside of the lid a loop of stiff wire, bent in
the shape shown at (_e_). This may be fastened to the cover by
means of small staples, or even tacks, and should project over
the edge about two inches. When this is done, the lid should be
raised to the angle shown in our illustration, and the spot where
the end of the wire loop touches the back of the box should be
marked and a slit cut through the wood at this place, large enough
for the angle of the loop to pass through. Two elastics should
now be fastened to the inside of the box, being secured to the
bottom at the side, and the other to the edge of the cover, as
seen in the illustration. They should be sufficiently strong to
draw down the cover quickly. The perch, or spindle, should consist
of a light stick of wood, as shown at (_b_,) one end provided with
a slight notch, and the other fastened to the inside of the front
of the box by a string or leather hinge, (_c_,) keeping the notch on
the _upper_ side of the stick. It will be now seen that by opening
the cover, until the loop enters through the groove, and by then
hooking the notch in the spindle _under_ the loop as seen at (_a_)
the trap will be set, and if properly done it will be found that a
very slight weight on the spindle will set it free from the loop
and let the cover down with swiftness.
To secure the cover in place a small tin catch should now be applied
to the front edge of the box, as shown in the illustration. A piece
of tin two inches in length by a half an inch in breadth will answer
for this purpose. One end should be bent
[Page 89]
down half an inch at a pretty sharp angle, and the other attached
by two tacks, to the edge of the box, in the position shown in
the cut. This precaution will effectually prevent the escape of
whatever bird, large or small, the trap may chance to secure. It
is a necessary feature of the trap, as without it the elastics
might be torn asunder and the lid thereby easily raised.
[Illustration]
This trap may be baited in a variety of ways. As it is particularly
designed for a _bird_ trap, it is well to sprinkle the bottom of
the box with berries, bird-seed, small insects, such as crickets,
grasshoppers, etc. These latter are very apt to jump out, and it
may be well to fasten one or two of them to the bottom with a pin
through the body, just behind the head.
There are many kinds of birds which live almost exclusively on
insects; and as this bait is of rather a lively kind, there is
scarcely any other method to retain them in their position. A bird
on approaching this trap will almost irresistibly alight on the
perch, and if not at _first_, it is generally sure to do so before
long. If desired, a pasteboard platform may be fastened on the
[Page 90]
top of the perch with small tacks, and the bait scattered upon
it. This will act in the same manner, and might, perhaps, be a
trifle more certain. We will leave it to our readers to experiment
upon.
We have given this variety the name of "owl-trap," because it may
be used with success in this direction. When set for this purpose,
it should be baited with a live mouse, small rat or bird, either
fastened to the bottom of the trap, if a bird, or set in with the
trap inclosing it, if a mouse. A small bird is the preferable bait,
as it may be easily fastened to the bottom of the box by a string,
and as a general thing is more sure to attract the attention of
the owl by its chirping.
The trap should be set in an open, conspicuous spot, in the neighborhood
where the owls in the night are heard to "hoot." The chances are
that the box will contain an owl on the following morning.
This bird is a very interesting and beautiful creature, and if our
young reader could only catch one, and find rats and mice enough
to keep it well fed, he would not only greatly diminish the number
of rats in his neighborhood, but he would realize a great deal
of enjoyment in watching and studying the habits of the bird.
Should it be difficult to supply the above mentioned food, raw
meat will answer equally well. The bird should either be kept in
a cage or inclosure and in the latter case, its wings will require
to be clipped.
THE BOX BIRD TRAP.
Here we have another invention somewhat resembling the foregoing.
Our engraving represents the arrangement of the parts as the trap
appears when set.
[Illustration]
The box may be of almost any shape. A large sized cigar box has
been used with excellent success, and for small birds is just the
thing. The cover of the box in any case should work on a hinge of
some sort. The trap is easily made. The first thing to be done
is to cut an upright slot, about two inches in length, through
the centre of the backboard, commencing at the upper edge. To the
inside centre edge of the cover a small square strap, about four
inches in length, should then be secured. It should be so adjusted
as that one-half shall project toward the inside of the box, as
seen in the illustration, and at the same time pass easily through
[Page 91]
the slot beneath where the cover is closed. The lid should now be
supplied with elastics as described in the foregoing. Next in order
comes the bait stick. Its shape is clearly shown in our illustration,
and it may be either cut in one piece or consist of two parts joined
together at the angle. To the long arm the bait should be attached
and the upright portion should be just long enough to suspend the
cover in a position on a line with the top of the box. The trap may
now be set, as seen in our illustration, and should be supplied with
the necessary tin catch, described in the foregoing.
THE PENDENT BOX TRAP.
This invention is original with the author of this work, and when
properly made and set will prove an excellent device for the capture
of small birds.
The general appearance of the trap, as set, is clearly shown in
our illustration. A thin wooden box is the first requisite, it
should be about a foot square and six inches in depth, and supplied
with a close fitting cover, working on hinges. The sides should then
be perforated with a few auger holes for purposes of ventilation.
Two elastics are next in order, and they should be attached to the
cover and box, one on each side, as shown at (_a_.) They should be
drawn to a strong tension, so as to hold the cover firmly against
the box.
The mechanism of the trap centres in the bait stick which differs
in construction from any other described in this book.
It should be made about the size of a lead pencil, and eleven
[Page 92]
inches or so in length, depending of course upon the size of the
box.
It should then be divided in two pieces by a perfectly flat cut,
the longer part being six inches in length. This piece should be
attached to the back board of the box by a small string and a tack,
as shown at (_c_), its end being bluntly pointed. Its attachment
should be about five inches above the bottom board, and in the
exact centre of the width of the back.
[Illustration]
Near the flat end of the other piece the bait consisting of a berry
or other fruit, should be secured, and the further extremity of
the stick should then be rounded to a blunt point. The trap is now
easily set. Raise the lid and lift the long stick to the position
given in the illustration. Adjust the flat end of the bait stick
against that of the former, and allow the pressure of the lid to
bear against the blunt point of the short stick at (_d_), as shown
in the illustration, a straight dent being made in the cover to
receive it, as also in the back of the box for the other piece.
If properly constructed, this pressure will be sufficient to hold
the sticks end to end, as our engraving represents, and the trap is
[Page 93]
thus set. The slightest weight on the false perch thus made will
throw the parts asunder, and the cover closes with a snap.
The greatest difficulties in constructing the trap will be found
in the bearings of the bait sticks (_b_), the ends of which must
be perfectly flat and join snugly, in order to hold themselves
together. The box may now be suspended in a tree by the aid of a
string at the top. The first bird that makes bold enough to alight
on the perch is a sure captive, and is secured without harm. If
desired, the elastic may be attached to the inside of the cover,
extending to the back of the box, as seen in the initial at the head
of this chapter. If the elastic in any event shows tendencies toward
relaxing, the tin catch described on page 88 should be adjusted
to the lower edge of the box to insure capture.
THE HAWK TRAP.
[Illustration]
Our illustration represents a hawk in a sad plight. The memory of
a recent feast has attracted it to the scene of many of
[Page 94]
its depredations: but the ingenious farmer has at last outwitted
his feathered foe and brought its sanguinary exploits to a timely
end. This trap is a "Yankee" invention and has been used with great
success in many instances where the hawk has become a scourge to the
poultry yard. The contrivance is clearly shown in an illustration,
consisting merely of a piece of plank two feet square, set with
stiff perpendicular pointed wires.
This affair was set on the ground in a conspicuous place, the board
covered with grass, and the nice fat Poland hen which was tied to
the centre proved a morsel too tempting for the hawk to resist.
Hence the "fell swoop" and the fatal consequences depicted in our
illustration. The owl has also been successfully captured by the
same device.
THE WILD DUCK NET.
Following will be found two examples of traps in very common use
for the capture of wild ducks, and in the region of Chesapeake
bay, immense numbers of the game are annually taken by their aid.
The first is the well known net trap, so extensively used in nearly
all countries, both for the capture of various kinds of fish as
well as winged game. Our illustration gives a very clear idea of
the construction of the net, and an elaborate description is almost
superfluous. It consists of a graduated series of hoops covered
by a net work. From each a converging net extends backward ending
in a smaller hoop which is held in position by cords extending
[Page 95]
therefrom to the next larger hoop. The depth of these converging
nets should extend backward about three or four feet from the large
hoop; and the distance between these latter should be about five
feet. The length of the net should be about twenty feet, terminating
in a "pound" or netted enclosure, as seen in the illustration. The
trap may be set on shore or in the water as seen. "Decoy" birds are
generally used, being enclosed in the pound.
[Illustration]
When set on land the bait consisting of corn or other grain should
be spread about the entrance and through the length of the net.
It is remarkable that a duck which so easily finds its way within
the netted enclosure, should be powerless to make its escape, but
such seems to be the fact, and even a single hoop with its reflex
net, has been known to secure a number of the game.
THE HOOK TRAP
[Illustration]
Our second example is one which we are almost tempted to exclude
on account of its cruelty, but as our volume is especially devoted
to traps of all kinds and as this is a variety in very common use,
we feel bound to give it a passing notice. Our illustration fully
conveys its painful mode of capture, and a beach at low water is
generally the scene of the slaughter. A long stout cord is first
stretched across the sand and secured
[Page 96]
to a peg at each end. To this shorter lines are attached at intervals,
each one being supplied with a fish hook baited with a piece of
the tender rootstock of a certain water reed, of which the ducks
are very fond. The main cord and lines are then imbedded in the
sand, the various baits only appearing on the surface, and the
success of the device is equal to its cruelty.
THE "FOOL'S CAP" TRAP.
Of all oddities of the trap kind, there is, perhaps, no one more
novel and comical than the "Fool's Cap" crow-trap, which forms
the subject of our present illustration. Crows are by no means
easy of capture in any form of trap, and they are generally as
coy and as shrewd in their approach to a trap as they are bold in
their familiarity and disrespect for the sombre scarecrows in the
com field. But this simple device will often mislead the smartest
and shrewdest crow, and make a perfect _fool_ of him, for it is
hard to imagine a more ridiculous sight than is furnished by the
strange antics and evolutions of a crow thus embarrassed with his
head imbedded in a cap which he finds impossible to remove, and
which he in vain endeavors to shake off by all sorts of gymnastic
performance. The secret of the little contrivance is easily told.
The cap consists of a little cone of stiff paper, about three or
four inches in diameter at the opening. This is imbedded in the
ground, up to its edge, and a few grains of corn are dropped into
it. The inside edge of the opening is then smeared with _bird-lime_,
[Page 97]
a substance of which we shall speak hereafter.
[Illustration]
The crow, on endeavoring to reach the corn, sinks his bill so deep
in the cone as to bring the gummy substance in contact with the
feathers of his head and neck, to which it adheres in spite of
all possible efforts on the part of the bird to throw it off.
The cones may be made of a brownish-colored paper if they are to
be placed in the earth, but of white paper when inserted in the
snow. It is an excellent plan to insert a few of these cones in
the fresh corn hills at planting season, as the crows are always on
the watch at this time, and will be sure to partake of the tempting
morsels, not dreaming of the result. The writer has often heard
of this ingenious device, and has read of its being successfully
employed in many instances, but he has never yet had an opportunity
of testing it himself. He will leave it for his readers to experiment
upon for themselves.
BIRD LIME.
This substance so called to which we have above alluded, and which
is sold in our bird marts under that name, is a viscid, sticky
preparation, closely resembling a very thick and gummy varnish.
It is astonishingly "sticky," and the slightest quantity between
the fingers will hold them together with remarkable tenacity. What
its effect must be on the feathers of a bird can easily be imagined.
[Illustration]
This preparation is put up in boxes of different sizes, and may
be had from any of the taxidermists or bird-fanciers in any of
[Page 98]
our large towns or cities. Should a _home made_ article be required,
an excellent substitute may be prepared from the inner bark of the
"slippery elm." This should be gathered in the spring or early
summer, cut into very small pieces or scraped into threads, and
boiled in water sufficient to cover them until the pieces are soft
and easily mashed. By this time the water will be pretty much boiled
down, and the whole mass should then be poured into a mortar and
beaten up, adding at the same time a few grains of wheat. When
done, the paste thus made may be put into an earthen vessel and
kept. When required to be used, it should be melted or softened
over the fire, adding goose grease or linseed oil, instead of water.
When of the proper consistency it may be spread upon sticks or
twigs prepared for it, and which should afterwards be placed in
the locality selected for the capture of the birds.
An excellent bird-lime may be made also from plain linseed-oil,
by boiling it down until it becomes thick and gummy. Thick varnish
either plain or mixed with oil, but always free from alcohol, also
answers the purpose very well. The limed twigs may be either set
in trees or placed on poles and stuck in the ground.
If any of our readers chance to become possessed of an owl, they
may look forward to grand success with their limed twigs. It is a
well known fact in natural history that the _owl_ is the universal
enemy of nearly all our smaller birds. And when, as often happens,
a swarm of various birds are seen flying frantically from limb to
limb, seeming to centre on a particular tree, and filling the air
with their loud chirping, it may be safely concluded that some sleepy
owl has been surprised in his day-dozing, and is being severely
pecked and punished for his nightly depredations.
Profiting from this fact, the bird catcher often utilizes the owl
with great success. Fastening the bird in the crotch of some tree,
he adjusts the limed twigs on an sides, even covering the neighboring
branches with the gummy substance. No sooner is the owl spied by
_one_ bird than the cry is set up, and a _score_ of foes are soon
at hand, ready for battle. One by one they alight on the beguiling
twigs, and one by one find themselves held fast. The more they flutter
the more powerless they become, and the more securely are they held.
In this way many valuable and rare birds are often captured.
[Page 99]
THE HUMMING BIRD TRAP.
One of the most ingenious uses to which bird lime is said to have
been applied with success, is in the capture of humming-birds.
The lime in this instance is made simply by chewing a few grains
of wheat in the mouth until a gum is formed. It is said that by
spreading this on the inside opening of the long white lily or
trumpet-creeper blossom, the capture of a humming-bird is almost
certain, and he will never be able to leave the flower after once
fairly having entered the opening. There can be no doubt but that
this is perfectly practicable, and we recommend it to our readers.
The object in making the bird-lime from wheat consists in the fact
that this is more easily removed from the feathers than the other
kinds.
We would not wish our readers to infer from this that a humming-bird
might be captured or kept alive, for of all birds, they are the most
fragile and delicate, and would die of _fright_, if from nothing
else. They are chiefly used for ornamental purposes, and may be
caught in a variety of ways. A few silk nooses hung about the flowers
where the birds are seen to frequent, will sometimes succeed in
ensnaring their tiny forms.
The blow-gun is often used with good success, and the concussion
from a gun loaded simply with powder, and aimed in the direction
of the bird, will often stun it so that it will fall to the ground.
If a strong stream of water be forced upon the little creature, as
it is fluttering from flower to flower, the result is the same,
as the feathers become so wet that it cannot fly.
[Illustration]
[Page 101]
[Illustration: MISCELLANEOUS TRAPS]
[Page 103]