A SIMPLE METHOD OF BINDING MSS.
The method of binding described in this chapter is not intended to
take the place of proper binding in leather. However, it is sometimes
useful to be able to put the MS. in a cover when it is not desirable or
convenient to go to the expense of having the book bound in the usual
way. Binding with stiff boards is an art that requires considerable
experience as well as skilled training, but there is no reason why MSS.
should not be bound in limp vellum in the manner described here. No
special appliances are needed for this method, and the writer should be
able to complete his MSS. by binding them without any difficulty if the
directions given here are carefully followed.
Two additional sections of plain paper or vellum should be made, to
serve as end-papers, one at each end of the book. If the MS. is on
vellum, the end-papers should be of the same material, but if on paper
the end-papers should be made of paper of the same kind as that used
for the rest of the book.
Four strips of binder’s vellum should then be cut, these being about
3/8 in. wide and four inches long. The sections should be knocked
up quite squarely, and should be marked on the back with a soft
black-lead pencil in the manner shown in Fig. 46, using a square
to get the lines accurate. The sections should all be marked quite
distinctly so that each section shows the divisions quite plainly. This
gives the position of the four strips of vellum and the kettle-stitches
at each end. The mark for the kettle-stitch should be about ½ in. from
each end, although sometimes at the bottom a little more than this
is allowed. The position of the vellum strips should be in the same
proportion as given in Fig. 46.
[Illustration: FIG. 46.]
When ready to sew the sections, take the four vellum strips and
fold each one about 1½ in. or 1¾ in. at right angles from each end,
according to the thickness of the book. Then take a drawing-board and
place on the edge of it the first section face downwards, with the
four strips placed in position with their shorter ends underneath. Get
a needle, threaded with good silk or unbleached thread, and insert it
at the top kettle-stitch mark from the outside, bringing it out again
at the first mark for the vellum strip. Bring the thread round the
strip and re-insert the needle on the other side, bringing it out again
and round the next strip, and so on until it comes out at the bottom
kettle-stitch. When this is done it should have the effect, shown in
Fig. 46, of a continuous thread passing in and out and round the vellum
strips. Now take the next section and place it in position and sew in
the same manner, continuing with the same thread but in the reverse
manner. Upon coming to the loose end, where the needle was first
inserted, this should be tied up with it. Then add another section,
going backwards and forwards, adding section by section until the whole
is completed. Each kettle-stitch is linked up as shown in Fig. 46,
and it is a good plan also to link up the threads that cross over the
vellum strips in the same manner.
To keep the sections in position while stitching, a small paper-weight
is useful. The thread should be drawn fairly tightly, a fresh needleful
of thread being tied on to the end of the other when it is exhausted,
and when the stitching is completed the end should be carefully tied
up with the last kettle-stitch. The back may then be covered with thin
glue and lined with a piece of thin leather or tough paper, and the MS.
is then ready for covering. (See Fig. 49.)
A piece of binding vellum is cut for the cover and marked with a folder
on the underside, as shown in Fig. 47. The two lines marked down the
centre represent the thickness of the sections. The two spaces on
either side, exclusive of margins, should be slightly larger than the
size of the sides of the book. The wide margin that extends all the
way round may be approximately 1½ in., while the additional narrow
margin on two sides may be ¼ in. in width. The corners should be cut
along the dotted lines with a sharp knife.
[Illustration: Vellum Cover
FIG. 47.]
The cover is then folded up in the manner shown in Fig. 48. It is as
well to stick the edges down with a little stiff quick-drying paste.
The two narrow margins should be marked with the folder and folded over
to form two flaps on the fore-edge of the book. All these folds should
be made very carefully so as to ensure them being quite even. Some
people find it best to make a cover of stiff paper first, and, when
this fits correctly, they make the vellum cover exactly the same size.
It is possible by this method to avoid spoiling the vellum through
cutting it so that it does not fit.
[Illustration: Cover ready for binding the MS.
FIG. 48.]
The next thing to do is to mark the places on the inside of the cover
for the vellum strips to be laced through. These should be made about ¾
in. from the creases of the back. Another mark should be made about 3/8
in. away from the first mark. If the book is now placed in the cover it
will be quite an easy matter to mark exactly where the vellum strips
intersect these lines, and slits may be cut with a sharp knife in the
cover in the places marked with dotted lines in Fig. 48.
The vellum strips may now be laced through these slits and the ends
stuck down with strong paste. Some pieces of good silk ribbon may be
attached to the top and bottom strips and laced through the cover,
leaving the ends to tie, or the book may be left without these.
The two outside end-papers may then be pasted down on to the inside of
the vellum cover. This will cover up the ends of the vellum strips. It
is, however, essential that for all this a quick-drying paste should
be used and not one that is very liquid, as this would quickly strike
through and cockle the vellum. The end-papers should be pasted down
very neatly and then the book should be placed under pressure until it
is quite dry. One or two heavy books make a very good press for this
purpose.
[Illustration: MS. ready for insertion in Cover.
Finished Volume.
FIG. 49.]
When the book is quite dry the decoration of the cover may be proceeded
with. The title may be written on it with quite plain lettering or
it may be decorated in a more elaborate fashion. It is better not to
use raised gold, as it is very liable to get damaged on the cover of
the book. However, some very good effects can be obtained with flat
gilding. The vellum strips that are laced through the cover offer scope
for decoration. If it is desirable to write the title on the back of
the book it is better to do this before the book is bound, as it is
rather a difficult matter to write here when the book has been bound.
If it is desired to do so, the cover may be made of thin card or stout
paper in this way and then have a cover of vellum folded over it. If
this is done, the vellum strips will, of course, be covered up on the
outside, as well as the inside, of the cover.
Generally the books most suitable for this style of binding are small
ones, although larger MSS. are sometimes bound in this way.
The same remarks that were made with regard to the style of decoration
in the MS. itself apply equally here. The subject of the book must
decide, to a large extent, what style of ornament is to be used.
For example, a volume of modern poetry will require quite different
treatment to that of a mediæval romance.
It ought to be possible for the illuminator to make some very charming
little volumes in this manner.