FLYING AIRSHIPS, GONDOLAS, AND BIRDS (PLATE VI)
These toys are made in a somewhat similar manner to the merry-go-round.
Get a large reel (diameter about 1-1/2 inches). Next saw a piece of
stripwood, A B, 1/4" × 1/4" × 12-1/4". Glue and nail to the ends of this
cross-pieces of the same stripwood, 4-1/2 inches long. Make holes for
nails with a fine drill, otherwise the stripwood may split. Glue and
nail A B across the top of the reel as in Fig. 205.
[Illustration: FIG. 205]
Cut two pieces of stripwood, 1/4" × 1/4" × 6". Glue and nail
cross-pieces 4-1/4 inches long to one end of each of these. Glue and
nail them to the reel as in figure.
Next glue and nail another large reel to the centre of a board about
4 inches by 5-3/4 inches. Get a dowel rod that will fit the reels
(diameter about 1/4 inch), or file the ends of a square stick to fit;
this central pillar should be about 13 inches high. Glue this pillar
into the reel on the board and fit the other reel with the cross-pieces
on the top of the pillar.
[Illustration: FIG. 206]
The cars must next be made; they will hang by two strings from the ends
of the cross-pieces (Fig. 206). Grooves may be filed round the ends of
the cross-pieces for tying the cotton, or holes can be drilled in the
ends before the cross-pieces are fastened on.
The cars are made of paper, cardboard or wood. Fig. 207 shows the
pattern of a car. It should be 4-1/2 inches long and 2 inches wide.
The dotted lines show where the paper is to be bent, or in the case of
cardboard half cut and bent.
The width of the bottom of the car is 2 inches, the roof 2-3/4 inches;
this allows for bending, and makes a curved roof. The doors can be made
to meet if desired; in this case each door will be 1 inch wide.
Five, four or three windows may be cut in the sides, and windows in the
doors.
Paper seats may be fitted inside.
To hang the car a rod is cut, about 5 inches long, E F in Fig. 206,
and grooves are filed at each end. This is glued to the top of the car,
with the ends projecting. Pieces of cotton attach the beam E F to the
cross-piece. (Length of cotton, about 7 inches.)
[Illustration: FIG. 207]
A reel may be glued on the top of the arms for turning the airships;
cotton may be wound round this, and when pulled causes the cars to
revolve. Into the hole of the top reel may be inserted a stick bearing a
flag.
Paint the cars according to taste.
When the top reel is set spinning the cars fly round and outward in a
delightful manner, gradually returning to a vertical position as the
speed lessens.
=Gondolas.= For the cars gondolas may be substituted, as in Fig. 208.
These gondolas form simple and effective paper toys, even if not
attached to revolving arms.
Draw on stout paper or cardboard and cut out the two sides, A A, as in
Fig. 208. The total length of the boat should be 9 inches.
Next draw a line on a piece of paper, _a´ b´_ in Fig. 209, the same
length as _a b_ in Fig. 208. Divide the line into three parts at _c´_
and _d´_. _a´ c´_ represents the length _a c_ in Fig. 208; _c´ d´_ (not
shown to scale), the length of the cabin _c d_. If the full length of
the gondola is 9 inches, the length _a b_ will be about 8-1/2 inches,
and the length _a c_ should be 3 inches; this makes the length of the
cabin, _c d_, about 1-3/4 inches. Draw two lines at _c´_ and _d´_ at
right angles to _a´ b´_. Make _e f_ and _g h_ (Fig. 209) equal to the
widest part of the gondola. (If the length of 9 inches has been decided
on, the width of the gondola should be 1-1/4 inches.) Complete triangles
_a´ f e_ and _g b´ h_ as in Fig. 209; draw flanges as in diagram and
cut out. Two other triangles exactly the same size with flanges will be
required.
[Illustration: FIG. 208]
[Illustration: FIG. 209]
Now fasten together the bows, B, and the sterns, C, of the sides, A A
(Fig. 208), with seccotine, taking care that no gum comes below the line
_a b_. Gum the triangle _a´ f e_ (Fig. 209) to the sides, A A, as in
Fig. 208. Point _a_ must come at the very end of the sides A, and the
surface of _a f e_ forms the deck. Gum triangle _g h b´_ to the sides,
A, in the same way (Fig. 208). Now gum the other two triangles to the
bottom of the gondola. Their apexes will probably come at about K and M
in Fig. 208. The positions of these points can be determined by finding
out at what spot the triangle brings the sides A A closely together; try
to keep them as far from ends _a_ and _b_ as possible.
[Illustration: SWINGING BOATS AND GREAT WHEEL
(Chapter XIV)]
[Illustration: PLATE VI FLYING GONDOLAS, ETC.]
The space left between the two bottom triangles has a piece of paper
gummed over it.
[Illustration: FIG. 210]
Fig. 210 shows the shape of the cabin and the measurements required for
a cabin for a gondola of 9 inches. Four gondolas should be made. They
should be painted black and red, or black and yellow, according to taste.
The gondolas are hung from cross-pieces, like the airships, but the arms
should be 12-1/2 inches, and the cross-pieces 9 inches; the strings must
be of different lengths, since the bow is higher than the stern. Seats
may be put in the cabins if desired.
[Illustration: FIG. 211]
=Flying Birds.= Cut four arms as for the gondolas (stripwood 1/4" × 1/4"
will do), drill small holes at one end, glue and nail them to a reel.
Cut four short arms 3-1/2 inches and glue them on between the long arms
as in Fig. 211.
The birds are made of cardboard and corks. The birds from the long arms
should hang low down, and the birds from the short arms higher up. Cane
may be used for hanging the birds to the arms. The outer circle may be
hung with sea-gulls (Fig. 212), and the inner circle with swallows (Fig.
213), or all the birds may be swallows. When the reel is turned quickly
the birds in flight are very effective.
[Illustration: FIG. 212]
Fig. 212 shows how the sea-gull is made out of a cork and four pieces of
cardboard (one for the head, two for the wings, one for the tail). Paint
the cork white, paint eyes and a beak, mark a few feathers on the wings.
Figs. 213, 214, 215 show how the swallow is made.
[Illustration: FIG. 213]
[Illustration: FIGS. 214, 215]