CHAPTER XXIX

THE AUTOMATIC ELECTRIC COMPANY'S SYSTEM

Almost wherever automatic telephony is to be found--and its use is

extensive and rapidly growing--the so-called Strowger system is

employed. It is so named because it is the outgrowth of the work of

Almon B. Strowger, an early inventor in the automatic telephone art.

That the system should bear the name of Strowger, however, gives too

great prominence to his work and too little to that of the engineers of

the Automatic Electric Company under the leadership of Alexander E.

Keith.

=Principles of Selecting Switch.= The underlying features of this

automatic system have already been referred to in the abstract. A better

grasp of its principles may, however, be had by considering a concrete

example of its most important piece of apparatus--the selecting switch.

The bare skeleton of such a switch, sufficient only to illustrate the

salient point in its mode of operation, is shown in Fig. 380. The

essential elements of this are a vertical shaft capable of both

longitudinal and rotary motion; a pawl and ratchet mechanism actuated by

a magnet for moving the shaft vertically a step at a time; another pawl

and ratchet mechanism actuated by another magnet for rotating the shaft

a step at a time; an arm carrying wiper contacts on its outer end,

mounted on and moving with the shaft; and a bank of contacts arranged on

the inner surface of a section of a cylinder adapted to be engaged by

the wiper contacts on this movable arm.

These various elements are indicated in the merest outline and with much

distortion in Fig. 380, which is intended to illustrate the principles

of operation rather than the details as they actually are in the system.

In the upper left-hand corner of this figure, the magnet shown will, if

energized by impulses of current, attract and release its armature and,

in doing so, cause the pawl controlled by this magnet to move the

vertical shaft of the switch up a step at a time, as many steps as

there are impulses of current. The vertical movement of this shaft will

carry the wiper arm, attached to the lower end of the shaft, up the same

number of steps and, in doing so, will bring the contacts of this wiper

arm opposite, but not engaging, the corresponding row of stationary

contacts in the semi-cylindrical bank. Likewise, through the ratchet

cylinder on the intermediate portion of the shaft, the magnet shown at

the right-hand portion of this figure will, when energized by a

succession of electrical impulses, rotate the shaft a step at a time, as

many steps as there are impulses. This will thus cause the contacts of

the wiper arm to move over the successive contacts in the row opposite

to which the wiper had been carried in its vertical movement.

[Illustration: Fig. 380. Principles of Automatic Switch]

At the lower left-hand corner of this figure, there is shown a pair of

keys either one of which, when operated, will complete the circuit of

the magnet to which it is connected, this circuit including a common

battery. In a certain rough way this pair of key switches in the lower

left-hand corner of the drawing may be taken as representing the

call-transmitting apparatus at the subscriber's station, and the two

wires extending therefrom may be taken as representing the line wires

connecting that subscriber's station to the central office; but the

student must avoid interpreting them as actual representations of the

subscriber's station calling apparatus or the subscriber's line since

their counterparts are not to be found in the system as it really

exists. Here again accuracy has been sacrificed for ease in setting

forth a feature of operation.

Still referring to Fig. 380, it will be seen that the bank contacts

consist of ten rows, each having ten pairs of contacts. Assume again,

for the sake of simplicity, that the exchange under consideration has

one hundred subscribers and that each pair of bank contacts represents

the terminals of one subscriber's line. Assume further that the key

switches in the lower left-hand corner of the figure are being

manipulated by a subscriber at that station and that he wishes to obtain

a connection with line No. 67. By pressing and releasing the left-hand

key six times, he will cause six separate impulses of current to flow

through the upper left-hand magnet and this will cause the switch shaft

to move up six steps and bring the wiper arm opposite the sixth row of

bank contacts. If he now presses and releases his right-hand key seven

times, he will, through the action of the right-hand magnet, rotate the

shaft seven steps, thus bringing the wipers into contact with the

seventh contact of the sixth row and thus into contact with the desired

line. As the wiper contacts on the switch arm form the terminals of the

calling subscriber's line, it will be apparent that the calling

subscriber is now connected through his switch with the line of

subscriber No. 67.

As stated, each of the pairs of bank contacts are connected with the

line of a subscriber; the line, Fig. 380, is shown so connected to the

forty-first pair of contacts, that is to the first contact in the fourth

row. The selecting switch shown in Fig. 380 would be for the sole use of

the subscriber on the line No. 41. Each of the other subscribers would

have a similar switch for his own exclusive use. Since any of the

switches must be capable of reaching line No. 67, for instance, when

moved _up_ six rows and _around_ seven, it follows that the

sixty-seventh pair of contacts in each bank of the entire one hundred

switches must also be connected together and to line No. 67. The same

is, of course, true of all the contacts corresponding to any other

number. Multiple connections are thus involved between the corresponding

contacts of the banks, in much the same way as in the corresponding

jacks in the multiple of a manual switchboard. As a result of this

multiple connection of the bank contacts, any subscriber may move the

wiper arm of his selecting switch into connection with the line of any

other subscriber.

_The "Up-and-Around" Movement._ The elemental idea to be grasped by the

discussion so far, is the so-called "up-and-around" method of action of

the selecting switches employed in this system. This preliminary

discussion may be carried a step further by saying that the arrangement

is such that when a subscriber presses both his keys and grounds both of

the limbs of his line, such a condition is brought about as will cause

all holding pawls to be withdrawn from the shaft, and thus allow it to

return to its normal position with respect to both its vertical and

rotary movements. No attempt has been made in Fig. 380 to show how this

is accomplished.

=Function of Line Switch.= Such a system as has been briefly outlined in

the foregoing would require a separate selecting switch for each

subscriber's line and would be limited to use in exchanges having not

more than one hundred lines. In the modern system of the Automatic

Electric Company, the requirement that each subscriber shall have a

selective switch, individual to his own line, has been eliminated by

introducing what is called an _individual line switch_ by means of which

any one of a group of subscribers' lines, making a call, automatically

appropriates one of a smaller group of selecting switches and makes it

its own only while the connection exists.

=Subdivision of Subscribers' Lines.= The limitation as to the size of

the exchange has been overcome, without increasing the number of bank

contacts in any selecting switch, by dividing the subscribers' lines

into groups of one hundred and causing selecting switches automatically

to extend the calling subscriber's line first into a group of groups

corresponding, for instance, to the thousand containing the called

subscriber's line, and then into the particular group containing the

line, and lastly, to connect with the individual line in that group.

=Underlying Feature of Trunking System.= It will be remembered that in

the chapter on fundamental principles of automatic systems, it was

stated that the subscriber, by means of the signal transmitter at his

station, was made to govern the action of the central-office apparatus

in the selection of a proper group of trunks; and the group being

selected, the central-office apparatus was made to act automatically to

pick out and connect with the first idle trunk of such group. This

selection by the subscriber of a group followed by the automatic

selection from among that group forms the basis of the trunking system.

It is impossible, by means of any simple diagram, to show a complete

scheme of trunking employed, but Fig. 381 will give a fundamental

conception of it. This figure shows how a single calling line, indicated

at the bottom, may find access into any particular line in an office

having a capacity for ten thousand.

=Names of Selecting Switches.= Selecting switches of the "up-and-around"

type are the means by which the calling line selects and connects with

the trunk lines required in building up the connection, and finally

selects and connects with the line of the called subscriber. Where such

a switch is employed for the purpose of selecting a _trunk_, it is

called a selector switch. It is a _first selector_ when it serves to

pick out a major group of lines, _i. e._, a group containing a

particular thousand lines or, in a multi-office system, a group

represented by a complete central office. It is a _second selector_ when

it serves to make the next subdivision of groups; a _third selector_ if

further subdivision of groups is necessary; and finally it is _a

connector_ when it is employed to pick out and connect with the

_particular line in the final group of one hundred lines_ to which the

connection has been brought by the selectors. In a single office of

10,000-line capacity, therefore, we would have first and second

selectors and connectors, the first selectors picking out the thousands,

the second selectors the hundreds, and the connectors the individual

line. In a multi-office system we may have first, second, and third

selectors and connectors, the first selector picking out the office, the

second selector the thousands in that office, the third selector the

hundreds, and the connector the individual lines.

=The Line Switch.= In addition to the selectors and connectors there are

line switches, which are comparatively simple, one individual to each

line. Each of these has the function, purely automatic, of always

connecting a line, as soon as a call is originated on it, to some one of

a smaller group of first selectors available to that line. This idea may

be better grasped when it is understood that, in the earlier systems of

the Automatic Electric Company, there was a first selector permanently

associated with each line. By the addition of the comparatively simple

line switch, a saving of about ninety per cent of the first selectors

was effected, since the number of first selectors was thereby reduced

from a number equal to the number of lines in a group to a number equal

to the number of simultaneous connections resulting from calls

originating in that group. In other words, by the line switch, the

number of first selectors is determined by the traffic rather than by

the number of lines.

=Scheme of Trunking.= With this understanding as to the names and

broader functions of the things involved, Fig. 381 may now be

understood. The line switch of the single line, as indicated here, has

only the power of selection among three trunks, but it is to be

understood that in actual practice, it would have access to a greater

number, usually ten. So, also, throughout this diagram we have shown the

apparatus and trunks arranged in groups of three instead of in groups of

ten, only the first three thousands groups being indicated and the first

three hundreds groups in each thousand. Again only three levels instead

of ten are indicated for each selecting switch, it being understood that

in the diagram the various levels are represented by concentric arcs of

circles, and the trunk contacts by dots on these arcs.

_Line-Switch Action._ When the subscriber, whose line is shown at the

bottom of the figure, begins to make a call, the line switch acts to

connect his line with one of the first selector trunks available to it.

This selection is entirely preliminary and, except to start it, is in no

way under the control of the calling subscriber. The calling line now

has under its control a first selector which, for the time being,

becomes individual to it. Let it be assumed that the line switch found

the first of the first selector trunks already appropriated by some

other switch, but that the second one of these trunks was found idle.

This trunk being appropriated by the line switch places the center one

of the first selectors shown under the control of the subscriber's line.

This first selector then acts in response to the first set of selective

impulses sent out by his signal transmitter.

[Illustration: DEAN HARMONIC CONVERTER Dry Cell Type for Magneto

Exchange. _The Dean Electric Co._]

[Illustration: Fig. 381. Scheme of Trunking]

_First Selector Action._ We will assume that the calling subscriber

desires to connect with No. 3213. The first movement of the subscriber's

signal transmitter will send, therefore, three impulses over the line.

These impulses will act on the vertical magnet of the first selector

switch to move it up three steps. On this "level" of the contact bank of

this switch all of the contacts will represent second selector trunks

leading to the _third_ thousand group. The other ends of these trunks

will terminate in the wipers and also in the controlling magnets of

second selectors serving this thousand. This function on the part of the

first selector controlled by the act of the subscriber will have thus

selected a _group_ of trunks leading to the _third_ thousand, but the

subscriber has nothing to do with which one of the trunks of this group

will actually be used. Immediately following the vertical movement of

the first selector switch the rotary movement of this switch will start

and will continue until the wipers of that switch have found contacts of

an idle trunk leading to a second selector. Assuming that the first

trunk was the one found idle, the first selector wipers would pause on

the first pair of contacts in the third level of its bank, and the trunk

chosen may be seen leading from that contact off to the group of second

selectors belonging to the third thousand. For clearness, the chosen

trunks in this assumed connection are shown heavier than the others.

_Second Selector Action._ The next movement of the dial by the

subscriber in establishing his desired connection will send two

impulses, it being desired to choose the _second_ hundred in the _third_

thousand. The first selector will have become inoperative before this

second series of impulses is sent and, therefore, only the second

selector will respond. Its vertical magnet acting under the influence of

these two impulses will step up its wiper contacts opposite the second

row of bank contacts, and the subscriber will thus have chosen the

_group_ of trunks leading to the _second_ hundred in the _third_

thousand. Here, again, the automatic operation of picking out the first

idle one of this chosen group of trunks will take place without the

volition of the subscriber, and it will be assumed that the first two

trunks on this level of the second selector were found already engaged

and that the third was therefore chosen. The connection continues, as

indicated by heavy lines in Fig. 381, to the third one of the connectors

in the _second_ hundred of the _third_ thousand. Any one of these

connectors would have accomplished the purpose but this is assumed to be

the first one found idle by the second selector.

_Connector Action._ The third movement of the subscriber's dial will

send but one impulse, this corresponding to the _first_ group of ten in

the _second_ hundred in the _third_ thousand. This impulse will move the

connector shaft up to the first level of bank contacts; and from now on

the action of the connector differs radically from that of the

selectors. The connector is not searching for an idle trunk in the group

but for a particular line and, therefore, having chosen the group of ten

lines in the desired hundred, the connector switch waits for further

guidance from the subscriber. This comes in the form of the final set of

impulses sent by the subscriber's signal transmitter which, in this

case, will be three in number, corresponding to the final digit in the

number of the called subscriber. This series of impulses will control

the rotary movement of the connector wipers which will move along the

first level and stop on the third one. The process is seen to be one of

successive selection, first of a large group, then of a smaller, again

of a smaller, and finally of an individual.

If the line is found not busy, the connection between the two

subscribers is complete and the called subscriber's bell will be rung.

If it is found busy, however, the connector will refuse to connect and

will drop back to its normal position, sending a busy signal back to the

calling subscriber. The details of ringing and the busy-back operation

may only be understood by a discussion of drawings, subsequently to be

referred to.

=Two-Wire and Three-Wire Systems.= In most of the systems of the

Automatic Electric Company in use today the impulses by which the

subscriber controls the central-office apparatus flow over one side of

the line or the other and return by ground. The metallic circuit is used

for talking and for ringing the called subscriber's bell, while ground

return circuits, on one side of the line or the other, are used for

sending all the switch controlling impulses.

Recently this company has perfected a system wherein no ground is

required at the subscriber's station and no ground return path is used

for any purpose between the subscriber and the central office.

This later system is known as the "two-wire" system, and in

contra-distinction to it, the earlier and most used system has been

referred to as the "three-wire." It is not meant by this that the line

circuits actually have three wires but that each line employs three

conductors, the two wires of the line and the earth. The three-wire

system will be referred to and described in detail, and from it the

principles of the two-wire system will be readily understood.

[Illustration: Fig. 382. Automatic Wall Set]

[Illustration: Fig. 383. Automatic Desk Stand]

=Subscriber's Station Apparatus.= The detailed operation of the

three-wire system may be best understood by considering the subscriber's

station apparatus first. The general appearance of the wall set is shown

in Fig. 382, and of the desk set in Fig. 383. These instruments embody

the usual talking and call-receiving apparatus of a common-battery

telephone and in addition to this, the signal transmitter, which is the

thing especially to be considered now. The diagrammatic illustration of

the signal transmitter and of the relation that its parts bear to the

other elements of the telephone set is shown in Fig. 384. It has already

been stated that the subscriber manipulates the signal transmitter by

rotating the dial on the face of the instrument. A clearer idea of this

dial and of the finger stop for it may be obtained from Figs. 382 and

383.

[Illustration: Fig. 384. Circuits of Telephone Set]

_Operation._ To make a call for a given number the subscriber removes

his receiver from its hook, then places his forefinger in the hole

opposite the number corresponding to the first digit of the desired

number. By means of the grip thus secured, he rotates the dial until its

movement is stopped by the impact of the finger against the stop. The

dial is then released and in its return movement it sends the number of

impulses corresponding to the first digit in the called number. A

similar movement is made for each digit.

In Fig. 384 is given a phantom view of the dial, in order to show more

clearly the relation of the mechanical parts and contacts controlled by

it. For a correct idea of its mechanical action it must be understood

that the shaft _1_, the lever _2_, and the interrupter segment _3_ are

all rigidly fastened to the dial and move with it. A coiled spring

always tends to move the dial and these associated parts back to their

normal positions when released by the subscriber, and a centrifugal

governor, not shown, limits the speed of the return movement.

The subscriber's hook switch is mechanically interlocked with the dial

so as to prevent the dial being moved from its normal position until the

hook is in its raised position. This interlocking function involves also

the pivoted dog _4_. Normally the lower end of this dog lies in the path

of the pin _5_ carried on the lever _2_, and thus the shaft, dial, and

segment are prevented from any considerable movement when the receiver

is on the hook. However, when the receiver is removed from its hook, the

upwardly projecting arm from the hook engages a projection on the dog

_4_ and moves the dog out of the path of the pin _5_. Thus the dial is

free to be rotated by the subscriber. The pin _6_ is mounted in a

stationary position and serves to limit the backward movement of the

dial by the lever _2_ striking against it.

Ground Springs:--Five groups of contact springs must be considered, some

of which are controlled wholly by the position of the switch hook,

others jointly by the position of the switch hook and the dial, others

by the movement of the dial itself, and still others by the pressure of

the subscriber's finger on a button. The first of these groups consists

of the springs _7_ and _8_, the function of which is to control the

continuity of the ground connection at the subscriber's station. The

arrangement of these two springs is such that the ground connection will

be broken until the subscriber's receiver is removed from its hook. As

soon as the receiver is raised, these springs come together in an

obvious manner, the dog _4_ being lifted out of the way by the action of

the hook. The ledge on the lower portion of the spring _7_ serves as a

rest for the insulated arm of the dog _4_ to prevent this dog, which is

spring actuated, from returning and locking the dial until after the

receiver has been hung up.

Bell and Transmitter Springs:--The second group is that embracing the

springs _9_, _10_, _11_, and _12_. The springs _10_ and _11_ are

controlled by the lower projection from the switch hook, the spring

_11_ engaging the spring _12_ only when the hook is down. The spring

_10_ engages the spring _9_ only when the hook lever is up and not then

unless the dial is in its normal position. While the hook is raised,

therefore, the springs _9_ and _10_ break contact whenever the dial is

moved and make contact again when it returns to its normal position. The

springs _11_ and _12_ control the circuit through the subscriber's bell

while the springs _9_ and _10_ control the continuity of the circuit

from one side of the line to the other so as to isolate the limbs from

each other while the signal transmitter is sending its impulses to the

central office.

Impulse Springs:--The third group embraces springs _13_, _14_, and _15_

and these are the ones by which the central-office switches are

controlled in building up a connection.

Something of the prevailing nomenclature which has grown up about the

automatic system may be introduced at this point. The movements of the

selecting switches at the central office are referred to as _vertical_

and _rotary_ for obvious reasons. On account of this the magnet which

causes the vertical movement is referred to as the _vertical magnet_ and

that which accomplishes the _rotary_ movement as the _rotary magnet_. It

happens that in all cases the selecting impulses sent by the

subscriber's station, corresponding respectively to the number of digits

in the called subscriber's number, are sent over one side of the line

and in nearly all cases these selecting impulses actuate the vertical

movements of the selecting switches. For this reason the particular limb

of the line over which the selecting impulses are sent is called the

_vertical limb_. The other limb of the line is the one over which the

single impulse is sent after each group of selecting impulses, and it is

this impulse in every case which causes the selector switch to start

rotating in its hunt for an idle trunk. This side of the line is,

therefore, called _rotary_. For the same reasons the impulses over the

vertical side of the line are called _vertical impulses_ and those over

the rotary side, _rotary impulses_. The naming of the limbs of the line

and of the current impulses _vertical_ and _rotary_ may appear odd but

it is, to say the least, convenient and expressive.

Coming back to the functions of the third group of springs, _13_, _14_,

and _15_, _15_ may be called the _vertical spring_ since it sends

vertical impulses; _13_, the _rotary spring_ since it sends rotary

impulses; and _14_, the _ground spring_ since, when the hook is up, it

is connected with the ground.

On the segment _3_ there are ten projections or cams _16_ which, when

the dial is moved, engage a projection of the spring _15_. When the dial

is being pulled by the subscriber's finger, these cams engage the spring

_15_ in such a way as to move it away from the ground spring and no

electrical contact is made. On the return of the dial, however, these

cams engage the projection on the spring _15_ in the opposite way and

the passing of each cam forces this vertical spring into engagement with

the ground spring. It will readily be seen, therefore, by a

consideration of the spacing of these cams on the segment and the finger

holes in the dial that the number of cams which pass the vertical spring

_15_ will correspond to the number on the hole used by the subscriber in

moving the dial.

Near the upper right-hand corner of the segment _3_, as shown in Fig.

384, there is another projection or cam _17_, the function of which is

to engage the rotary spring _13_ and press it into contact with the

ground spring. Thus, the first thing that happens in the movement of the

dial is for the projection _17_ to ride over the hump on the rotary

spring and press the contact once into engagement with the ground

spring; and likewise, the last thing that happens on the return movement

of the dial is for the rotary spring to be connected once to the ground

spring after the last vertical impulse has been sent.

If both the rotary and vertical sides of the line are connected with the

live side of the central-office battery, it follows that every contact

between the vertical and the ground spring or between the rotary and the

ground spring will allow an impulse of current to flow over the vertical

or the rotary side of the line.

We may summarize the action of these impulse springs by saying that

whenever the dial is moved from its normal position, there is, at the

beginning of this movement, a single rotary impulse over the rotary side

of the line; and that while the dial returns, there is a series of

vertical impulses over the vertical side of the line; and just before

the dial reaches its normal position, after the sending of the last

vertical impulse, there is another impulse over the rotary side of the

line.

The mechanical arrangements of the interrupter segment _3_ and its

associated parts have been greatly distorted in Fig. 384 in order to

make clear their mode of operation. This drawing has been worked out

with great care, with this in mind, at a sacrifice of accuracy in regard

to the actual structural details.

Ringing Springs:--The fourth group of springs in the subscriber's

telephone is the ringing group and embraces the springs _18_, _19_, and

_20_. The springs _19_ and _20_ are normally closed and maintain the

continuity of the talking circuit. When, however, the button attached to

the spring _19_--which button may be seen projecting from the instrument

shown in Fig. 382, and from the base of the one shown in Fig. 383--is

pressed, the continuity of the talking circuit is interrupted and the

vertical side of the line is connected with the ground. It is by this

operation, after the connection has been made with the desired

subscriber's line, that the central-office apparatus acts to send

ringing current out on that line.

Release Springs:--The fifth set of springs is the one shown at the

left-hand side of Fig. 384, embracing springs _21_, _22_, and _23_. The

long curved spring _21_ is engaged by the projecting lug on the switch

hook when it rises so as to press this spring away from the other two.

On the return movement of the hook, however, this spring is pressed to

the left so as to bring all three of them into contact, and this, it

will be seen, grounds both limbs of the line at the subscriber's

station. This combination cannot be effected by any of the other springs

at any stage of their operation, and it is the one which results in the

energization of such a combination of relays and magnets at the central

office as will release all parts involved in the connection and allow

them to return to their normal positions ready for another call.

_Salient Points._ If the following things are borne in mind about the

operation of the subscriber's station apparatus, an understanding of the

central-office operations will be facilitated. First, the selective

impulses always flow over the vertical side of the line; they are always

preceded and always followed by a single impulse over the rotary side of

the line. The ringing button grounds the vertical side of the line and

the release springs ground both sides of the line simultaneously.

=The Line Switch.= The first thing to be considered in connection with

the central-office apparatus is the line switch. This, it will be

remembered, is the device introduced into each subscriber's line at the

central office for the purpose of effecting a reduction of the number of

first selectors required at the central office, and also for bringing

about certain important functional results in connection with trunking

between central and sub-offices. The function of the line switch in

connection with the subscriber's line, however, is purely that of

reducing the number of first selectors.

The line switches of one hundred lines are all associated to form a

single unit of apparatus, which, besides the individual line switches,

includes certain other apparatus common to those lines. Such a group of

one hundred line switches and associated common apparatus is called a

_line-switch unit_, or frequently, a _Keith unit_. Confusion is likely

to arise in the mind of the reader between the individual line switch

and the line-switch unit, and to avoid this we will refer to the piece

of apparatus individual to the line as the line switch, and to the

complete unit formed of one hundred of these devices as a line-switch

unit.

_Line and Trunk Contacts._ Each line switch has its own bank of contacts

arranged in the arc of a circle, and in this same arc are also placed

the contacts of each of the ten individual trunks which it is possible

for that line to appropriate. The contacts individual to the

subscriber's line in the line switch are all multipled together, the

arrangement being such that if a wedge or plunger is inserted at any

point, the line contacts will be squeezed out of their normal position

so as to engage the contacts of the trunk corresponding to the

particular position in the arc at which the wedge or plunger is

inserted. A small plunger individual to each line is so arranged that it

may be thrust in between the contact springs in the line-switch bank in

such manner as to connect any one of the trunks with the line terminals

represented in that row, the particular trunk so connected depending on

the portion of the arc toward which the plunger is pointed at the time

it is thrust in the contacts.

These banks of lines and trunk contacts are horizontally arranged, and

piled in vertical columns of twenty-five line switches each. The ten

trunk contacts are multipled vertically through the line-switch banks,

so that the same ten trunks are available to each of the twenty-five

lines. We thus have, in effect, an old style, Western Union, cross-bar

switchboard, the line contacts being represented in horizontal rows and

the trunk contacts in vertical rows, the connection between any line and

any trunk being completed by inserting a plunger at the point of

intersection of the horizontal and the vertical rows corresponding to

that line and trunk.

_Trunk Selection._ The plungers by which the lines and trunks are

connected are, as has been said, individual to the line, and all of the

twenty-five plungers in a vertical row are mounted in such manner as to

be normally held in the same vertical plane, and this vertical plane is

made to oscillate back and forth by an oscillating shaft so as always

_to point the plungers toward a vertical row of trunk contacts that

represent a trunk that is not in use at the time_. The to-and-fro

movement of this oscillating shaft, called the _master bar_, is

controlled by a master switch and the function of this master switch is

always to keep the plungers pointed toward the row of contacts of an

idle trunk. The thrusting movement of the individual plungers into the

contact bank is controlled by magnets individual to the line and under

control of the subscriber in initiating a call. As soon as the plunger

of a line has been thus thrust into the contact bank so as to connect

the terminals of that line with a given trunk, the plunger is no longer

controlled by the master bar and remains stationary. The master bar then

at once moves all of the other plungers that are not in use so that they

will point to the terminals of another trunk that is not in use. The

plungers of all the line switches in a group of twenty-five are,

therefore, subject to the oscillating movements of the master bar when

the line is not connected to a first selector trunk. As soon as a call

is originated on a line, the corresponding plunger is forced into the

bank and is held stationary in maintaining the connection to a first

selector trunk, and all of the other plungers not so engaged, move on so

as to be ready to engage another idle trunk.

_Trunk Ratio._ The assignment of ten trunks to twenty-five lines would

be a greater ratio of trunks than ordinary traffic conditions require.

This ratio of trunks to lines is, however, readily varied by multipling

the trunk contacts of several twenty-five line groups together. Thus,

ten trunks may be made available to one hundred subscribers' lines by

multipling the trunks of four twenty-five line switch groups together.

In this case the four master bars corresponding to the four groups of

twenty-five line switches are all mechanically connected together so as

to move in unison under the control of a single master switch. If more

than ten and less than twenty-one trunks are assigned to one hundred

lines, then each set of ten trunks is multipled to the trunk contacts of

fifty line switches, the two master bars of these switches being

connected together and controlled by a common master switch.

_Structure of Line Switch._ The details of the parts of a line switch

that are individual to the line are shown in Fig. 385, the line and

trunk contact bank being shown in the lower portion of this figure and

also in a separate view in the detached figure at the right. A detailed

group of several such line switches with the oscillating master bar is

shown in Fig. 386. This figure shows quite clearly the relative

arrangement of the line and trunk contact banks, the plungers for each

bank, and the master bar.

[Illustration: Fig. 385. Line Switch]

In practice, four groups of twenty-five line switches each are mounted

on a single framework and the group of one hundred line switches,

together with certain other portions of the apparatus that will be

referred to later, form a line-switch unit. A front view of such a unit

is shown in Fig. 387. In order to give access to all portions of the

wiring and apparatus, the framework supporting each column of fifty line

switches is hinged so as to open up the interior of the device as a

whole. A line-switch unit thus opened out is shown in Fig. 388.

[Illustration: Fig. 386. Portion of Line-Switch Unit]

_Circuit Operation._ The mode of operation of the line switch may be

best understood in connection with Fig. 389, which shows in a schematic

way the parts of a line switch that are individual to a subscriber's

line, and also those that are common to a group of fifty or one hundred

lines. Those portions of Fig. 389 which are individual to the line are

shown below the dotted line extending across the page. The task of

understanding the line switch will be made somewhat easier if Figs. 385

and 389 are considered together. The individual parts of the line switch

are shown in the same relation to each other in these two figures with

the exception that the bank of line and trunk springs in the lower

right-hand corner of Fig. 389 have been turned around edgewise so as to

make an understanding of their circuit connections possible.

[Illustration: Fig. 387. Line-Switch Unit]

[Illustration: Fig. 388. Line-Switch Unit]

[Illustration: Fig. 389. Circuits of Line-Switch Unit]

The vertical and rotary sides of the subscriber's line are shown

entering at the lower left-hand corner of this figure, and they pass to

the springs of the contact bank. Immediately adjacent to these springs

are the trunk contacts from which the vertical and the rotary limbs of

the first selector trunk proceed. The plunger is indicated at _1_, it

being in the form of a wheel of insulating material. It is carried on

the rod _2_ pivoted on a lever _3_, which, in turn, is pivoted at _4_ in

a stationary portion of the framework. A spring _5_, secured to the

underside of the lever _3_ and projecting to the left beyond the pivot

_4_ of this lever, serves always to press the right-hand portion of the

lever _3_ forward in such direction as to tend to thrust it into the

contact bank. The plunger is normally held out of the contact bank by

means of the latch _6_ carried on the armature _7_ of the trip magnet.

When the trip magnet is energized it pulls the armature _7_ to the left

and thus releases the plunger and allows it to enter the contact bank.

[Illustration: POWER SWITCHBOARD FOR MEDIUM-SIZED OFFICE Mercury Arc

Rectifier Panel and Transformer at Right.]

The master bar is shown at _8_, and a feather on this bar engages a

notch in the segment attached to the rear end of the plunger rod _2_.

This master bar is common to all of the plunger rods and by its

oscillatory movement, under the influence of the master switch, it

always keeps all of the idle plunger bars pointed toward the contacts of

an idle trunk. As soon, however, as the trip magnet is operated to cause

the insertion of a plunger into the contact bank, the feather on the

master bar is disengaged by the notch in the segment of the plunger rod,

and the plunger rod is, therefore, no longer subject to the oscillating

movement of the master bar.

When the release magnet is energized, it attracts its armature _9_ and

this lifts the armature _7_ of the trip magnet so that the latch _6_

rides on top of the left-hand end of the lever _3_. Then, when the

release magnet is de-energized, the spring _5_, which was put under

tension by the latch, moves the entire structure of levers back to its

normal position, withdrawing the plunger from the bank of contacts. The

notch on the edge of the segment of the plunger rod, when thus released,

will probably not strike the feather on the master bar, and the plunger

rod will thus not come under the control of the master bar until the

master bar has moved, in its oscillation, so that the feather registers

with the notch, after which this bar will move with all the others.

If, while the plunger is waiting to be picked up by the master bar, the

same subscriber should call again, his line will be connected with the

same trunk as before. There is no danger in this, however, that the

trunk will be found busy, because the master bar will not have occupied

a position which would make it possible for any of the lines to

appropriate this trunk during the intervening time.

_Master Switch._ Associated with each master bar there is a master

switch which determines the position in which the master bar shall stop

in order that the idle plungers may be pointed always to the contacts of

an idle trunk. The arm _10_ of this switch is attached to the master bar

and oscillates with it and serves to connect the segment _11_

successively with the contacts _12_, which are connected respectively to

the third, or release wire of each first selector trunk. In the figure

the arm _10_ is shown resting on the sixth contact of the switch and

this sixth contact is connected to a spring _13_ in the line-switch

contact bank that has not yet been referred to. As soon as the plunger

is inserted into the contact bank, the spring _14_ will be pressed into

engagement with the spring _13_, and this spring _14_ is connected with

the live side of the battery through the release magnet winding.

The contact strip _11_ on the master switch is thus connected through

the release magnet to the battery and from this current flows through

the left-hand winding of the master-switch relay. This energizes this

relay and causes the closure of the circuit of the locking magnet which

magnet unlocks the master bar to permit its further rotation. The

unlocking of the master bar brings the spring _15_ into engagement with

_16_ and thus energizes the master magnet, the armature of which

vibrates back and forth after the manner of an electric-bell armature,

and steps the wheel _17_ around. The wheel _17_ is mechanically

connected to the master bar so that each complete revolution of the

wheel will cause one complete oscillation of the master bar. The master

bar will thus be moved so as to cause all the idle plungers to sweep

through an arc and this movement will stop as soon as the master-switch

arm _10_ connects the arc _11_ with one of the contacts _12_ that is not

connected to the live side of the battery through the springs _13_ and

_14_ of some other line switch. It is by this means that the plungers of

the line switches are always kept pointing at the contacts of an idle

trunk. The way in which this feature has been worked out must demand

admiration and accounts for the marvelous quickness of this line switch.

The fact that the plungers are pointed in the right direction before the

time comes for their use, leaves only the simple thrusting motion of the

plunger to accomplish the desired connection immediately upon the

initiation of a call by the subscriber.

_Locking Segment._ It will be understood that the locking segment _18_

and the master-switch contact finger _10_ are both rigidly connected

with the master bar _8_ and move with it, the locking segment _18_

serving always to determine accurately the angular position at which the

master bar and the master-switch arm are brought to rest.

_Bridge Cut-Off._ One important feature of automatic switching,

particularly as exemplified in the system of the Automatic Electric

Company, is the disconnection, after its use, of each operating magnet

of each piece of apparatus involved in making a connection. Since these

operating magnets are always bridged across the line at the time of

their operation and then cut off after they have performed their

function, this feature may be referred to as the _bridge cut-off_.

_Guarding Functions._ Still another feature of importance is the means

for guarding a line or a piece of apparatus that has already been

appropriated or made busy, so that it will not be appropriated or

connected with for use in some other connection. For this latter purpose

contacts and wires are associated with each piece of apparatus, which

are multipled to similar contacts on other pieces of apparatus in much

the same way and for a similar purpose that the test thimbles in a

multiple switchboard are multipled together. Such wires and contacts in

the Automatic Electric Company's apparatus are called _private wires_

and _contacts_.

The bridge cut-off and guarding functions are provided for in the line

switch by a bridge cut-off relay shown in Fig. 389 and also in Fig. 385,

it being the upper one of the individual line relays in each of those

figures. This bridge cut-off relay is operated as soon as the plunger of

the line is thrust into the bank; the contacts _19_ and _20_, closed by

the plunger, serving to complete the circuit of this relay. To make

clear the bridge cut-off feature it will be noted that the trip magnet

of a line switch is connected in a circuit traced from the rotary side

of the line through the contacts _21_ and _22_ of the bridge cut-off

relay, thence through the coil of the trip magnet to the common wire

leading to the spring _23_ of the master-bar locking device and thence

to the live side of the battery. Obviously, therefore, as soon as the

bridge cut-off relay operates, the trip magnet becomes inoperative and

can cause no further action of the line switch because its circuit is

broken between the springs _21_ and _22_.

The private or guarding feature is taken care of by the action of the

plunger in closing contacts _19_ and _20_, since the private wire

leading to the bridge cut-off relay is, as has already been stated,

connected to ground when these contacts are closed. This private wire

leads off and is multipled to the private contacts on all the connectors

that have the ability to reach this line, and the fact that this wire

is grounded by the line switch as soon as it becomes busy, establishes

such conditions at all of the connectors that they will refuse to

connect with this line as long as it is busy, in a way that will be

pointed out later on.

_Relation of Line Switch and Connectors._ The vertical and rotary wires

of the subscriber's line are shown leading off to the connector banks at

the left-hand side of Fig. 389, and one side of this connection passes

through the contacts _24_ and _25_ of the bridge cut-off relay on the

line switch. It is through this path that a connection from some other

line through a connector to this line is established and it is seen that

this path is held open until the bridge cut-off relay of the line switch

is operated. For such a connection to this line the bridge cut-off relay

of the line switch is operated over the private wire leading from the

connector, and the operation of the bridge cut-off relay at this time

serves to render inoperative the line switch, so that it will not

perform its usual functions should the called subscriber start to make a

call after his line had been seized.

_Summary of Line-Switch Operation._ To summarize the operation of a line

switch when a call is originated on its line, the first movement of the

calling subscriber's dial will ground the rotary side of the line and

operate the trip magnet. This will cause the plunger to be inserted into

the bank, and thus extend the line to the first selector trunk through

the closing of the right-hand set of springs shown in the lower

right-hand corner of Fig. 389. The insertion of the plunger will also

connect the battery through the left-hand winding of the master-switch

relay and, by the sequence of operations which follows, cause the master

bar to move all of the idle plungers so as to again point them to an

idle trunk. The closure of contacts _19_ and _20_ by the plunger causes

the operation of the bridge cut-off relay which opens the circuit of the

trip magnet, rendering it inoperative; and also establishes ground

potential on all the private wire contacts of that line in the banks of

the connectors, so as to guard the line and its associated apparatus

against intrusion by others. The line is cut through, therefore, to a

first selector and all of the line-switch apparatus is completely cut

off from the talking circuit.

It must be remembered that all of the actions of the line switch, which

it has taken so long to describe, occur practically instantaneously and

as a result of the first part of the first movement of the subscriber's

dial. The line switch has done its work and "gone out of business"

before the selective impulses of the first digit begin to take place.

=Selecting Switches.= The first selector is now in control of the

calling subscriber. The circuits and elements of the first selector

switch are shown in Fig. 390. The general mechanical structure of the

first selectors, second selectors, and connectors, is the same and may

be referred to briefly here. Fig. 391 shows a rear view of a first

selector; Fig. 392, a side view of a second selector; and Fig. 393, a

front view of a connector. The arrangement of the vertical and rotary

magnets, of the selector shafts, and of the contact banks are identical

in all three of these pieces of apparatus and all these switches work on

the "up-and-around principle" referred to in connection with Fig. 380.

It is thought that with the general structure shown in Figs. 391, 392,

and 393 in mind, the actual operation may be understood much more

readily from Fig. 390.

Four magnets--the vertical, the rotary, the private, and the

release--produce the switching movements of the machine. These magnets

are controlled by various combinations brought upon the circuits by

three relays--the vertical, the rotary, and the back release. The fourth

relay shown, called the _off-normal_, is purely for signaling purposes,

as will be described.

_Side Switch._ Another important element of the selecting switches is

the so-called side switch which might better be called a pilot

switch--but we are not responsible for its name. This side switch has

for its function the changing of the control of the subscriber's line to

successive portions of the selector mechanism, rendering inoperative

those portions that have already performed their functions and that,

therefore, are no longer needed. This switch may be seen best in Fig.

392 just above the upper bank of contacts. It is shown in Fig. 390

greatly distorted mechanically so as to better illustrate its electrical

functions.

[Illustration: Fig. 390. Circuits of First Selector]

The contact levers _1_, _2_, _3_, and _4_ of the side switch are carried

upon the arm _5_ which is pivoted at _6_. All of these contact levers,

therefore, move about _6_ as an axis. The side switch has three

positions and it is shown, in Fig. 390, in the first one of these. When

the private magnet armature is attracted and released once, the

escapement carried by it permits the spring _7_ to move the arm _5_ so

as to bring the wipers of the side switch into its second position; the

second pulling up and release of the private magnet armature will cause

the movement of the side switch wipers into the third position. It is to

be noted that the escapement which releases the side switch arm may be

moved either by the private or by the rotary magnet, since the armature

of the latter has a finger which engages the private magnet armature.

[Illustration: Fig. 391. Rear View of First Selector]

_Functions of Side Switch._ The functions of the side switch may be

briefly outlined in connection with the first selector, as an example.

In the first position it extends the control of the subscriber's signal

transmitter through the first selector trunk and line relays to the

vertical and private magnets so that these magnets will be responsive to

the selecting impulses corresponding to the first digit. In its second

position it brings about such a condition of affairs that the rotary

magnet will be brought into play and automatically move the wipers over

the bank contacts in search of an idle trunk. In its third position,

both the vertical and rotary relays are cut off and the line is cut

straight through to the second selector trunk, and only those parts of

the first selector apparatus are left in an operative state which have

to do with the private or guarding circuits and with the release.

Similar functions are performed by the side switch in connection with

the other selecting switches.

[Illustration: Fig. 392. Side View of Second Selector]

_Release Mechanism._ Another one of the features of the switch that

needs to be considered before a detailed understanding of its operation

may be had, is the mechanical relation of the holding and the release

dog. This dog is shown at _8_ and, in the language of the art, is called

the _double dog_. As will be seen, it has two retaining fingers, one

adapted to engage the vertical ratchet and the other, the rotary ratchet

on the selector shaft. This double dog is pivoted at _9_ and is

interlinked in a peculiar way with the armature of the vertical magnet,

the armature of the release magnet, and the arm of the side switch. The

function of this double dog is to hold the shaft in whatever vertical

position it is moved by the vertical magnet and then, when the rotary

magnet begins to operate, to hold the shaft in its proper angular

position. It will be noted that the fixed dog _10_ is ineffective when

the shaft is in its normal angular position. But as soon as the shaft is

rotated, this fixed dog _10_ becomes the real holding pawl so far as the

vertical movement is concerned. The double dog _8_ is normally held out

of engagement with the vertical and the rotary ratchets by virtue of the

link connection, shown at _11_, between the release magnet armature and

the rear end of the double dog. On the previous release of the switch

the attraction of the release magnet armature permitted the link _11_ to

hook over the end of the dog _8_ and thus, on its return movement, to

pull this dog out of engagement with its ratchets. This movement also

resulted in pushing on the link _12_ which is pivoted to the side switch

arm _5_, and thus the return movement of the release magnet is made to

restore the side switch to its normal position. In order that the double

dog may be made effective when it is required, and in order that the

side switch may be free to move under the influence of the private

magnet, the double dog is released from its connection with the release

magnet armature by the first movement of the vertical magnet in a manner

which is clear from the drawing.

=First Selector Operation.= In discussing the details of operation of

the various selectors it will be found convenient to divide the

discussion according to the position of the side switch. This will bring

about a logical arrangement because it is really the side switch which

determines by its position the sequence of operation.

[Illustration: Fig. 393. Front View of Connector]

_First Position of Side Switch._ This is the position shown in Fig. 390,

and is the normal position. The vertical and the rotary lines extending

from the calling subscriber are continued by the levers _1_ and _2_ of

the side switch through the vertical and the rotary relay coils,

respectively, to the live side of battery. The lever _4_ of the side

switch in this position connects to ground the circuit leading from the

line switch through the release trunk, and the winding of the off-normal

relay. This winding is thus put in series with the release magnet of

the line switch, but on account of high resistance of the off-normal

relay no operation of the release magnet is caused. This will, however,

permit such current to flow through the release circuit as will energize

the sensitive off-normal relay and cause it to attract its armature and

light the off-normal lamp. If this lamp remains lighted more than a

brief period of time, it will attract notice and will indicate that the

corresponding selector has been appropriated by a line switch and that

for some reason the selector has gone no further. This lamp, therefore,

is an aid in preventing the continuance of this abnormal condition.

The first thing that happens after the line switch has connected the

calling subscriber with the first selector is a succession of impulses

over the vertical side of the line, this being the set of impulses

corresponding in number to the thousands digit or to the office, if

there is more than one. It will be understood that here we are

considering a single office of ten-thousand-line capacity or

thereabouts, and that, therefore, this first set of impulses corresponds

to the thousands digit in the called subscriber's line. Each one of

these impulses will flow from the battery through the vertical relay and

each movement of this relay armature will close the circuit of the

vertical magnet and cause the shaft of the selector to be stepped up to

the proper level. Immediately following the first series of selecting

impulses from the subscriber's station, a single impulse follows over

the rotary side of the line. This gives the rotary relay armature one

impulse and this in turn closes the circuit of the private magnet once.

The single movement of the private magnet armature allows the escapement

finger on the arm _5_ to move one step and this brings the side switch

contacts into the second position.

_Second Position of Side Switch._ In this position lever _4_ of the side

switch places a ground on the wire leading through the rotary magnet to

a source of interrupted battery current. The impulses which thus flow

through the rotary magnet occur at a frequency dependent upon the

battery interrupter and this is at a rate of approximately fifteen

impulses per second. The rotary magnet will step the selector shaft

rapidly around until something occurs to stop these impulses. This

something is the finding by the private wiper of an ungrounded private

contact in the bank, since all of the contacts corresponding to busy

trunks are grounded, as will be explained.

The action of the private magnet enters into this operation in the

following way: A circuit may be traced from the battery through the

private magnet to the third side switch wiper when in its second

position, thence through the back release relay to the private wiper. If

the wiper is at the time on the private bank contact of a busy trunk, it

will find that contact grounded and the private magnet will be

energized. The energizing of this magnet will not, however, cause the

release of the side switch. It must be energized and de-energized. The

private magnet armature will, therefore, be operated by the finger of

the rotary magnet armature on the first rotary step. The private magnet

will be energized and hold its armature operated if the private wiper

finds a ground on the first bank contact and will stay energized as long

as the private wiper is passing over private contacts of busy trunks.

Its armature will not be allowed to fall back during the passage of the

wiper from one trunk to another, because during that interval the finger

of the rotary magnet will hold it operated. As soon, however, as the

private wiper reaches the private bank contact of an idle trunk, no

ground will be found and the circuit of the private magnet will be left

open. When the impulse through the rotary magnet ceases, the private

magnet armature will fall back and the side switch will be released to

its third position.

_Third Position of Side Switch._ The first thing to be noted in this

position is that the calling line is cut straight through to the second

selector trunk, the connection being clean with no magnets bridged

across or tapped off. The third wiper of the side switch, when in its

third position, is grounded and this connects the release wire of the

second selector trunk, on which the switch wipers rest, through the

private wiper, the winding of the back release magnet, and the third

wiper of the side switch to ground. This establishes a path for the

subsequent release current through the back release magnet; and, of

equal importance, it places a ground on the private bank contact of that

trunk so that the private wiper of any other switch will be prevented

from stopping on the contacts of this trunk in the same manner that the

wiper of this switch was prevented from stopping on other trunks that

were already in use.

The fourth lever on the side switch, when in its third position, serves

merely to close the circuit of the rotary off-normal lamp. This lamp is

for the purpose of calling attention to any first selector switch that

has been brought into connection with some second selector trunk and

which, for some reason, has failed in its release. These off-normal

lamps are so arranged that they may be switched off manually to avoid

burning them during the hours of heaviest traffic. At night they afford

a ready means of testing for switches that have been left off-normal,

since the manual switches controlling these lamps may then be closed,

and any lamps which burn will show that the switches corresponding to

them are off-normal. Simple tests then suffice to show whether they are

properly or improperly in their off-normal position.

_Release of the First Selector._ As will be shown later, the normal way

of releasing the switches is from the connector back over the release

wire. It is sufficient to say at this point that when the proper time

for release comes, an impulse of current will come back over the second

selector trunk release wire through the private wiper, to the back

release relay magnet, and thence to ground through the third wiper of

the side switch which is in its third position. It may be asked why the

back release magnet was not energized during the previous operations

described, when current passed through it. The reason for this is that

in those previous operations the private magnet was always included in

series in the circuit and on account of the high resistance of the

private magnet, sufficient current did not pass through the back release

magnet to energize it.

When the back release relay is energized, it closes the circuit of the

release magnet and thus, through the link _11_, draws the double dog

away from its engagement with the shaft ratchets and at the same time,

through the link _12_, restores the side switch to its normal position.

Whenever the release magnet is operated it acts as a relay to close a

pair of contacts associated with it and thus to momentarily ground the

release wire of the first selector trunk extending back to the line

switch. Referring to Fig. 389, it will be seen that this path leads

through the contacts _13_ and _14_ and the release magnet to the

battery. It is by this means that the line switch is released, the

release impulse being relayed back from the first selector.

=Second Selector Operation.= For the purpose of considering the action

of the second selector, we will go back to the point where the first

selector had connected with a second selector trunk and where its side

switch had moved into its third position. In this condition, it will be

remembered, the trunk line was cut through to a second selector trunk

and all first selector apparatus cleared from the talking circuit.

The second selector chosen is one corresponding to the thousands group

as determined by the first digit of the called subscriber's number. The

circuits of a second selector are shown in Fig. 394 and it must be borne

in mind that the mechanical arrangements for producing the vertical and

the rotary movement of the shaft and for operating the side switch are

practically the same as those of the first selector. As in the first

selector, the sequence of operation is controlled by the successive

positions of the side switch, the first position permitting the

selection of the hundreds corresponding to the vertical impulses, the

second position allowing the selector to search for an idle trunk in

that hundred, and the third position cutting the trunk through and

clearing the circuit of obstructing apparatus.

_First Position of Side Switch._ The first thing that happens when the

subscriber begins to move his dial in the transmission of the second

series of selecting impulses is the sending of a preliminary impulse

over the rotary side of the line. This, in the case of the second

selector, energizes the rotary relay which, in turn, energizes the

private magnet; but the private magnet in the case of the second

selector can do nothing toward the release of the side switch because

the projection _5'_, on the side switch arm _5_, meets a projection on

the rear of the selector shaft which thus prevents the movement of the

side switch arm _5_ until the selector shaft has been moved out of its

normal position.

Immediately after the establishment of the connection to the selector,

the second set of selecting impulses comes in over the vertical wire

from the subscriber's station. These impulses, corresponding in number

to the hundreds digit, will energize the vertical relay and cause it, in

turn, to energize the vertical magnet, stepping up the selector shaft to

the level corresponding to the hundred sought. The single rotary

impulse, which follows just before the subscriber's dial reaches its

normal position, will energize the rotary relay of the second selector.

This, in turn, energizes the private magnet which makes a single

movement of its armature and allows the escapement finger on the side

switch arm to move one step and bring the side switch contacts into the

second position.

[Illustration: Fig. 394. Circuits of Second Selector]

_Second Position of Side Switch._ No detailed discussion of this is

necessary, since, with the side switch in its second position, the

actions which occur in causing the wipers of the second selector to seek

and connect with an idle trunk line, are exactly the same as in the case

of the first selector. When the second selector wipers finally reach a

resting place on the bank contacts, the private magnet armature,

operated during the hunting process, is released and the side switch is

thus shifted into the third position.

_Third Position of Side Switch._ The moving of the side switch into its

final position brings about the same state of affairs with respect to

the second selector that already exists with respect to the first

selector. The trunk line is cut straight through and all bridge circuits

or by-paths from it are cut off. The same guarding conditions are

established to prevent other lines or other pieces of apparatus from

making connections that will interfere with the one being established,

and the same provisions are made for working the back release when the

proper impulse comes from the connector, and for passing this back

release impulse on to the first selector in the same way that the first

selector passes it on to the line switch. The line of the calling

subscriber has now been extended to a connector, and that connector is

one of a group--usually ten--which alone has the ability to reach the

particular hundred lines containing the line of the desired subscriber.

The selection has, therefore, been narrowed down from one in ten

thousand to one in one hundred.

=The Connector=--_Its Functions._ It has already been stated that the

connector is of the same general type of apparatus as the first and the

second selectors. Unlike the first and the second selectors, however,

the connector is required to make a double selection under the guidance

of the subscriber. The first selector makes a single selection of a

group under the guidance of the subscriber and then an automatic

selection in that group not controlled by the subscriber. So it is with

the second selector. The connector, however, makes a selection of a

group of ten under the guidance of the subscriber and then, again under

the guidance of the subscriber, it picks out a particular one of that

group.

The connector also has other functions in relation to the ringing of

the called subscriber and the giving of a busy signal to the calling

subscriber in case the line wanted is found busy. It has still other

functions in that the talking current, which is finally supplied to

connected subscribers, is supplied through paths furnished by it.

_Location of the Connectors._ Connectors are the only ones of the

selecting switches that are in any sense individual to the subscribers'

lines. None of them is individual to a subscriber's line, but it may be

said that a group of ten connectors is individual to a group of one

hundred subscribers' lines. Since each group of one hundred lines has a

group of connectors of its own and since each one hundred lines also has

a line-switch unit of its own, and since the lines of this group must be

multipled through the bank contacts of the connectors of this individual

group and through the bank contacts of the line switches of this

particular unit, it follows that on account of the wiring problems

involved there is good reason for mounting the connectors in close

proximity to the line switches representing the same group of lines.

Some help in the grasping of this thought may result if it be remembered

that the line switch is, so to speak, the point of entry of a call and

that the connector is the point of exit, and, in order to reduce the

amount of wiring and to economize space, the point of exit and the point

of entry are made as close together as possible.

The relative locations and grouping of the line switches and connectors

are clearly shown in Fig. 395, which is a rear view of the same

line-switch unit that was illustrated in Figs. 387 and 388.

[Illustration: GAS ENGINE AND POWER BOARD Citizens' Telephone Co.,

Racine, Wis. _The Dean Electric Co._]

=Operation of the Connector.= The circuits of the connector are shown in

Fig. 396. In addition to the features that have been pointed out in the

first and the second selectors, all of which are to be found, with some

modifications, perhaps, in the connector, there must be considered the

features in the connector of busy-signal operation, of ringing the

called subscriber, of battery supply to both subscribers, and of the

trunk release operation. These may be best understood by tracing through

the operations of the connector from the time it is picked up by a

second selector until the connection is finally completed, or until the

busy signal has been given in case completion was found impossible. As

in the first and the second selectors, the sequence of operations is

determined by the position of the side switch.

[Illustration: Fig. 395. Connector Side of Line-Switch Unit]

[Illustration: Fig. 396. Circuits of Connector]

_First Position of Side Switch._ The connector in a ten-thousand-line

system is the recipient of the impulses resulting from the third and

fourth movements of the subscriber's dial. Considering the third

movement of the subscriber's dial, the first impulse resulting from it

comes over the rotary side of the line and results in the rotary relay

attracting its armature once. This results in a single impulse through

the private magnet which, however, does nothing because the projection

_5'_ strikes against a projection on the selector shaft. These two

projections interfere only when the selector shaft is in its normal

position. Then follows the series of impulses from the subscriber's

station corresponding to the tens digit in the called subscriber's

number. These pass over the vertical side of the line and through the

vertical relay, energizing that relay a corresponding number of times.

The vertical magnet, as in the case of the first and the second

selectors, is included in the circuit controlled by the vertical relay

and this results in the connector shaft being stepped up to the level

corresponding to the particular tens group containing the called

subscriber's number. It will be noted that the impulses from the

vertical side of the line, which cause this selection, pass through one

winding _13_ of the calling battery supply relay. This relay is operated

by these vertical selecting impulses, but in this position of the side

switch the closure of its local circuits accomplishes nothing.

Immediately after the tens group of selecting impulses over the vertical

side of the line, there follows a single rotary impulse from the

subscriber's station which, as in the case of the first and the second

selectors, energizes the rotary relay and causes it to give one impulse

to the private magnet. This impulse is now able, since the shaft has

moved from its normal position, to release the side switch arm one

notch, and the side switch, therefore, moves into its second position.

_Second Position of Side Switch._ It is principally in this second

position of the side switch that the connector selecting function

differs from that of the first and the second selector. There is no

trunk to be hunted, but rather the rotary movement of the connector

wipers must be made in response to the impulses, from the subscriber's

station, which correspond to the units digit in the selected number. The

first impulse corresponding to the fourth movement of the subscriber's

dial is a rotary one, and, as usual, it passes through the rotary relay

winding and this, in turn, gives an impulse to the private magnet. The

private magnet at this time has already released the side switch arm to

its second position, but it is unable to release it further because of a

feather on the wiper shaft--which projects just far enough to engage the

lug _5'_, when the shaft is in its normal angular position--thus

preventing the side switch arm from moving farther than its second

position.

Then follows over the vertical side of the line the last set of

selecting impulses corresponding to the units digit. This, as before,

energizes the vertical relay, but in the second position of the side

switch, it is to be noted, that the vertical relay no longer controls

the vertical magnet; the side switch has shifted the control of the

vertical relay to the rotary magnet. The rotary magnet is, therefore,

energized a number of times corresponding to the last digit in the

called number and the wipers of the connectors are thus brought to the

contacts of the line sought--their final goal. At this point many things

may happen, and the things that do happen depend on whether the called

subscriber's line is idle or busy.

Called-Line Busy:--It will first be assumed that the called line is

busy. The testing operation at the connectors occurs in the second

position of the side switch. If the called line is busy, it will be

either because it is connected to by some other connector or because it

has itself made a call. In the former case the private contacts of that

line in the banks of all the connectors serving that hundreds group of

lines will be grounded through the private wiper of some other

connector. That this is so, may be seen by tracing the circuit from the

private wiper on the shaft to the third side switch wiper which is

grounded in the third position; the other connector that has already

engaged the line will, of course, have its side switch in its final, or

third position. Again, if the line called is busy, because a call has

already been made from this line to some other line, the private

contacts on the connectors corresponding to the line will be grounded,

as will be seen by tracing from the private bank contacts, which are

shown in Fig. 396, through the private wire to the line switch, which is

shown in Fig. 389, and from thence to ground through the springs _19_

and _20_, which are brought together when the line switch is operated.

In any event, therefore, the determining condition of a busy line is

that its private bank contacts on all connectors of its group shall be

grounded. Under the present assumed condition, therefore, the connector

wipers, which have been brought to the bank contacts of the desired

line, will find a ground at the private bank contact. The connector

shaft stops for an instant on the contacts of this busy line and

immediately there follows over the rotary side of the line the

inevitable single rotary impulse. This energizes the rotary relay and

this, as usual, energizes the private magnet. Remembering now that the

connector side switch is in its second position and that the private

wiper of the connector has found a ground, we may trace back from the

private wiper through the third side switch wiper to its second contact;

thence through the contact springs _14_ and _15_, closed by the private

magnet; thence through the release magnet; thence through the contact

springs _16_ and _17_ of the calling battery supply relay to the live

side of the battery. This calling battery supply relay will, at this

time, have its core energized because the coil _18_ is in series with

the rotary relay coil which, as just stated, was energized by the last

rotary impulse. This series of operations has led to the energizing of

the release magnet, and, as a result, the double dog of the connector is

pulled out of the connector shaft ratchets and the shaft and the side

switch are restored to their normal position.

Busy-Back Signal:--The connector has dropped back to normal in all

respects. The calling subscriber, not knowing this, presses his ringing

button. This grounds the vertical side of the line at his station and

operates the vertical relay at the connector. This steps the shaft of

the connector up one step and causes the closure of the contacts _19_

and _20_ at the top of the connector shaft. This establishes a

connection to a circuit carrying periodically interrupted battery

current on which an inductive hum is placed. This circuit may be traced

from this source through the springs _20_ and _19_ to the first wiper of

the side switch, thence through the normally closed contacts of the

ringing relay to the rotary side of the line, and the varying potential

to which this path is subjected produces an inductive flow back to the

calling subscriber's telephone, and gives him the necessary signal which

consists of a hum or buzzing noise with which all users of automatic

systems soon become familiar.

Release on Busy Connection:--The connector, since its last release, has

been stepped up one notch and must again be released. When the

subscriber hangs up his receiver after receiving the busy signal, he

grounds both sides of his line momentarily by the action of the springs

_21_, _22_, and _23_ of Fig. 384. This operates the rotary and the

vertical relays on the connector simultaneously and brings together for

the first time the springs _21_ and _22_ of Fig. 396. This establishes a

connection from the battery through the springs _16_ and _17_ on the

calling battery supply relay, thence through the release magnet of the

connector, thence through the springs _22_ and _21_ of the vertical and

the rotary relay, thence through the release trunk back to the second

selector. From here the circuit passes through the private wiper of that

selector and the back release relay to ground through the third side

switch wiper which is in the third position. Considering this circuit in

respect to its action on the connector it is obvious that it energizes

the release magnet on the connector which restores the connector to

normal as before. At the second selector this circuit passed through the

back release relay, which closed a circuit through the release magnet

and through the back release relay contacts, thence back over the second

selector release trunk to the back release relay of the first selector,

and through the third wiper of the side switch on that selector to

ground, since that side switch also is in its third position. The

current through this circuit energizes the release magnet of the second

selector and restores it to its normal position and also energizes the

back release relay of the first selector. This, in turn, closes the

circuit from the battery through the release magnet of the first

selector and contacts of the back release relay to ground. This works

the release magnet of the first selector and restores that selector to

normal. The contacts on the first selector release magnet, shown in Fig.

390, are closed by the action of the release magnet and this closes the

path from ground back through the first selector release wire, and

through the contacts _13_ and _14_ of the line switch, through the line

switch release magnet to battery, and this restores the line switch to

normal.

The reason for the term _back release_ will now be apparent. The release

operation at the connector is relayed back to the second selector; that

of the second selector back to the first selector; and that of the first

selector back to the line switch. Until this plan was adopted, the

release magnet of each selector and connector involved in a connection

was left bridged across the talking circuit so as to be available for

release; and it sometimes occurred that a first selector would be

released before a second selector or connector, which latter switches

would thus be left off-normal until rescued by an attendant. The back

release plan makes it impossible for the connection necessary for the

release of a switch to be torn down until the release is actually

accomplished.

Called Line Found Idle:--It will be remembered that, before the

digression necessary to trace through the operations occurring upon the

finding of a busy line, the connector wipers had been brought, by the

influence of the calling subscriber's impulses, into engagement with the

contacts of the desired line; that the connector side switch was in its

second position; and that the final rotary impulse following the last

series of selecting impulses had not been sent. The condition now to be

assumed is that the called subscriber's line is free and the private

wiper, therefore, has found and rests on an ungrounded private bank

contact. The final rotary impulse which immediately follows will operate

the rotary relay and this, in turn, will operate the private magnet.

This happened under the assumed condition that the line was busy, but in

that case the release magnet was also operated at the same time and

restored all conditions to normal. Under the present condition the

operation of the private magnet will perform its usual function and move

the side switch of the connector into its third position.

_Third Position of Side Switch._ When the side switch of the connector

moves to its third position, it, as usual, cuts the talking circuit

straight through from the vertical and the rotary sides of the trunk

leading from the previous selector to the outgoing terminal of the

subscriber's line, which may be traced upon Fig. 396 back through the

line switch, shown in Fig. 389. Several things are to be noted about the

talking circuit so established: First, the inclusion of the condensers

in the vertical and the rotary sides of the connector circuit. The

purpose of this will be referred to later. Second, the inclusion in this

circuit at the connector of a pair of normally closed contacts in the

ringing relay. It may be said in passing that the ringing relay

corresponds exactly in function to a ringing key in a manual

switchboard. Third, the talking circuit leading from the connector to

the called subscriber's line passes on one side through the springs _24_

and _25_ of the bridge cut-off relay of the line switch, which is shown

in Fig. 389. These springs are normally open and would prevent the

completion of the talking circuit but for the fact that the bridge

cut-off relay of the line switch is energized over the private wire

leading to the connector bank and then through the connector wiper to

the third side switch wiper which, at this time, is in its third

position. The talking circuit is thus complete. The operation of this

bridge cut-off relay on the line switch has not only completed the

talking circuit but it has also opened the circuit of the trip magnet of

the line switch so as to prevent the operation of the trip magnet by the

subscriber on that line in case he should attempt to make a call during

the interval between the time when his line was connected with by the

connector and the time when he answers the call.

The third wiper of the connector side switch when moved into its third

position, puts the ground on all of the private bank contacts of the

line chosen and thus guards that line against connection by others, as

already described. It also operates the bridge cut-off relay of the line

switch as just mentioned.

The fourth wiper of the side switch, when moved into its third position,

establishes such a connection as will place the ringing relay under the

control of the vertical relay. This may be seen by tracing from ground

to the vertical relay springs _23_ and _24_, thence through the normally

closed upper pair of contacts on the private magnet, thence through the

fourth wiper on the side switch to its third contact, thence through the

ringing relay magnet, and through the springs _16_ and _17_ of the

calling battery supply relay and to battery. The calling battery supply

relay winding being in series with the vertical relay winding, the two

operate together and close the two normally open points in the ringing

relay circuit. This ringing relay acts as an ordinary ringing key and

connects the generator to the called subscriber's line in an obvious

manner, at the same time opening the talking circuit back of the ringing

relay in order to prevent the ringing current chattering the relays in

the circuit back of it. All that remains now is for the called

subscriber to respond. When he does he closes the metallic circuit of

the line through his talking apparatus.

_Battery Supply to Connected Subscriber._ Throughout the whole process

of building up a connection, it will be remembered that both sides of

the calling line are connected through the respective vertical and

rotary relays involved in building up the connection with the live side

of the battery. At the time when the connection is finally established

and the called subscriber rung, both sides of the calling line are

connected through various relay windings to the live side of the

battery. Such a condition leaves both sides of the line at the same

potential and, therefore, there is no tendency for current to flow

through the calling subscriber's talking apparatus, even though it is

connected across the circuit of the line. It remains, therefore, to be

seen how these conditions are so changed after the building up of a

connection as to supply the calling subscriber with talking current.

The calling subscriber can get no current until the called subscriber

responds. When the connection is first made with the called subscriber's

line, battery connection to his line is made from the live side of

battery through the normally closed contacts of the calling battery

supply relay, thence through the winding _25_ of the called battery

supply relay to the vertical side of the called line. The grounded side

of the battery is connected to the rotary side of his line through the

third wiper of the connector and the coil _26_ of the called battery

supply relay. As a result, this subscriber receives proper talking

current through the coils _25_ and _26_, and this relay is operated by

the flow of this current. The operation of this called battery supply

relay merely shifts the connection of the rotary side of the calling

subscriber's line from its normal battery connection, to ground, and

thus the battery is placed straight across the calling subscriber's line

so as to supply talking current. This supply circuit to the calling

subscriber may be traced from the live side of the battery through the

winding _13_ of the calling battery supply relay and the winding of the

vertical relay to the vertical side of the line, and from the grounded

side of battery through the third side switch wiper in its third

position to the now closed pair of contacts in the called battery supply

relay through the coil _18_ of the calling battery supply relay and the

coil of the rotary relay to the rotary side of the line.

It will be noted that the system of battery supply is that of the

standard condenser and retardation coil scheme largely employed in

manual practice; and that aside from the coils through which the battery

current is supplied to the connected subscribers, there are no taps

from, or bridges across, the two sides of the talking circuit.

=Release after Conversation.= It remains now only to secure the

disconnection of the subscribers after they are through talking. When

the calling subscriber hangs up, the whole disconnection is brought

about, all of the apparatus, including connector, selectors, and line

switch, returning to normal. This is done by the back release system and

is accomplished in almost the same way as has already been described in

connection with the disconnect after an unsuccessful call. There is this

difference, however: after an unsuccessful call when the line called for

was found busy, the release was made while the connector side switch was

in its normal position. In the present case, the release must be made

with the connector side switch in its third position and with the

talking battery bridged across the metallic circuit rather than

connected between each limb of the line and ground. It must be

remembered that the calling battery supply relay, while traversed by

current during the conversation, is not magnetically energized because,

with the current flowing through the metallic circuit of the line, the

two windings exert a differential effect. As soon, however, as the

calling subscriber hangs up his receiver, this differential action

ceases, due to the grounding of both sides of the line at the

subscriber's station. This relay, therefore, operates and cuts off

battery from the called battery supply relay and this, in turn, releases

its armature and thus changes the connection of the rotary side of the

calling line from ground to live side of the battery. The normal

condition of the battery connection now being restored, both the

vertical and the rotary relays at the connector become operated, due to

the ground on both sides of the line at the subscriber's station, and

this, as we have seen, is the condition which brings about the operation

of the connector release magnet, and the relaying back of the disconnect

impulse successively through the selectors to the line switch.

=Multi-Office System.= In exchanges involving more than one office, the

same general principles and mode of operation already outlined apply. If

the total number of subscribers in the multi-office exchange is to be

less than ten thousand, then four digit numbers suffice, and the first

movement of the dial may be made to select the office into which the

connection is to go, the subscribers' lines being so numbered with

respect to the offices that each office will contain only certain

thousands. The choosing of the thousand by the calling subscriber,

therefore, takes care in itself of the choice of offices. Where,

however, a multi-office exchange is to provide for connections among a

greater number of lines than ten thousand and less than one hundred

thousand, then it will take five movements of the dial to make the

selection--the five movements corresponding either to the five digits in

a number or to the name of an office, as indicated on the dial, and the

four digits of a smaller number. The lines may all carry five digit

numbers or, what is considered better practice, may be designated by an

office name followed by a four digit number. In this latter case the

numbers of the subscribers' lines will in each case be contained in one

or more of the tens of thousands groups, no number having more than four

digits. And the first movement of the dial, whether the name or number

plan be adopted, will select an office; or, looking at it another way,

will select a group of ten thousand and this being done, the next four

successive movements of the dial will select the numbers in that ten

thousand in just the some way that has been already described.

Certain difficulties arise, however, in multi-office working due to the

fact that the three-wire trunks between offices would in most cases be

objectionable. As long as the trunks extend between the various groups

of apparatus in the same office, it is cheaper to provide three wires

for each of them than it is to make any additional complication in the

apparatus. Where the trunking is done between offices, however, the

system may be so modified as to work over two wire inter-office trunks.

_The Trunk Repeater._ The purpose of the trunk repeater is to enable the

inter-office trunking to be done over two wires. It may be said that the

trunk repeater is a device placed in the outgoing trunk circuit at the

office in which a call originates, which will do over the two wires of

the trunk leading from it to the distant office just the same thing that

the subscriber's signal transmitter does over the two wires of the

subscriber's lines. It has certain other functions in regard to feeding

the battery for talking purposes back to the calling subscriber's line,

taking the place in this respect of the calling battery feed relay in

the connector in a single office exchange.

[Illustration: Fig. 397. Circuits of Trunk Repeater]

The circuits of a trunk repeater are shown in Fig. 397. In considering

it, it must be understood that the three wires entering the figure at

the left are the vertical, rotary, and release wires of a second

selector trunk leading from the first selector banks in the same office.

The two wires leading from the right of the figure are those extending

to the distant office, and terminate there in second selectors. The

vertical and the rotary sides of this trunk as shown at the left will

receive the impulses from the subscriber's station coming through the

line switch and the first selector, as usual. The vertical impulses will

pass through the winding of the vertical relay and through the winding

_1_ of the calling battery supply relay and thence to battery, the same

as on a connector. These impulses will work the armatures of both of

these relays in unison. The movements of the vertical relay armature in

response to these impulses will cause corresponding impulses to flow

over a circuit which may be traced from ground, through the springs _3_

and _2_ of the vertical relay, the springs _4_ and _5_ of the bridged

relay _6_ and thence to the vertical side of the trunk and to the

distant office, where it passes into a second selector and through its

vertical relay to battery. Thus the vertical impulses are passed on over

the two-wire trunk to the second selector at the distant office. It

becomes necessary, however, to prevent these impulses from passing back

through the winding of the bridge relay _6_ and this is done by means of

the sluggish relay _7_. This relay receives local battery impulses in

unison with those sent over the trunk by the vertical relay, these being

supplied from the battery at the local office through the contacts _8_

and _9_ of the calling battery supply relay, which works in unison with

the vertical relay. These rapidly recurring impulses are too fast for

the sluggish relay _7_ to follow. And this relay merely pulls up its

armature and cuts off both sides of the trunk leading back to the first

selector. The rotary impulses are repeated to the rotary side of the

two-wire trunk in a similar way.

Considering now the operation of the trunk repeater in the reverse

direction, the action of the bridging relay _6_ is of vital importance.

Normally both sides of trunk line are connected to the live side of the

battery and, therefore, there is no difference of potential between them

and no tendency to operate the bridged relay. When the connection has

been fully established to the subscriber at the distant office, and that

subscriber has responded, the action of his battery supply relay will,

as before stated, change the connection of the rotary side of the line

from battery to ground, and thus bridge the battery at the distant

exchange across the trunk. This action will pull up the bridged relay

_6_ at the trunk repeater and will perform exactly the same function

with respect to the connection of the battery with the calling

subscriber's line. In other words, it will change the connection of the

rotary side of the calling line from battery to ground, thus

establishing the necessary difference in potential to give the calling

subscriber the necessary current for transmission purposes. The

disconnect feature is about the same as already described. When the

calling subscriber hangs up his receiver both the vertical and rotary

relays of the trunk repeater operate, which places the ground on both

sides of the two-wire trunk to the distant office, which is the

condition for releasing all of the apparatus there.

For the purpose of convenience the simplified diagram of Fig. 398 has

been prepared, which shows the complete connection from a calling

subscriber to a called subscriber in a multi-office exchange, wherein

the first movement of the dial is employed to establish the connection

to the proper office and the four succeeding movements to make a

selection among ten thousand lines in that office. This circuit,

therefore, employs at the first office the line switch, the first

selector, and the trunk repeater; and at the second office the second

selector, third selector, connector, and line switch.

The third selector is omitted from Fig. 398, but this will cause no

confusion, since it is exactly like the second selector. The circuits

shown are exactly like those previously described but in drawing them

the main idea has been to simplify the connections to the greatest

possible extent at a sacrifice in the clearness with which the

mechanical inter-relation of parts is shown. No correct understanding of

the circuits of an automatic system is possible without a clear idea of

the mechanical functions performed by the different parts, and,

therefore, we have described what are apparently the more complex

circuit drawings first. It is believed that the student, in attempting

to gain an understanding of this marvel of mechanical and electrical

intricacy, will find his task less burdensome if he will refer freely to

both the simplified circuit drawing of Fig. 398 and the more complex

ones preceding it. By doing so he will often be enabled to clear up a

doubtful circuit point from the simpler diagram and a doubtful

mechanical point from those diagrams which represent more clearly the

mechanical relation of parts.

[Illustration: Fig. 398. Connection between a Calling and a Called

Subscriber in an Automatic System]

=Automatic Sub-Offices.= Obviously, the system of trunking employed in

automatic exchanges lends itself with great facility to the subdivision

of an exchange into a large number of comparatively small office

districts and the establishment of branch offices or sub-offices at the

centers of these districts.

The trunking between large offices has already been described. An

attractive feature of the automatic system is the establishment of

so-called sub-stations or sub-offices. Where there is, in an outlying

district, a distinct group of subscribers whose lines may readily be

centered at a common point within that district and where the number of

such subscribers and lines is insufficient to establish a fully equipped

office, it is possible to establish a so-called sub-station or

sub-office connected with the main office of that district by trunk

lines. At this sub-office there are placed only line switches and

connectors. When a call is originated on one of these sub-office lines,

the line switch acts instantly to connect that line with one of the

trunks leading to the main office of that district, at which this trunk

terminates in a first selector. From there on, the connection is the

same as that in a system in which no sub-offices are employed. Calls

coming into this sub-office over trunk lines from the main office are

received on the connectors at the sub-office and the connection is made

with the sub-office line by the connector in the usual manner. This

arrangement, it is seen, amounts merely to a stretching of the connector

trunks for a given group of lines so that they will reach out from a

main office to a sub-office, it being more economical to lengthen the

smaller number of trunks and by so doing to decrease in length the

larger number of subscribers' lines.

=The Rotary Connector.= For certain purposes it becomes desirable in

automatic work to employ a special form of connector which will have in

itself a certain ability to make automatic selection of one of a group

of previously chosen trunks in much the same manner as the first and

second selectors automatically choose the first idle one of a group of

trunks.

Such a use is demanded in private branch-exchange working where a given

business establishment, for instance, has a plurality of lines

connecting its own private switchboard with the central office. The

directory number of all these lines is, for convenience, made the same,

and it is important, therefore, that when a person attempts to make a

connection with this establishment, he will not fail to get his

connection simply because the first one of these lines happens to be

busy. For such use a given horizontal row of connector terminals or a

part of such a row is assigned to the lines leading to the private

branch exchange and the connector is so modified as to have a certain

"discretionary" power of its own. As a result, when the common number of

all these lines is called, the connector will choose the first one, if

it is not already engaged by some other connector, but if it is, it will

pass on to the next, and so on until an idle one is found. It is only

when the connector has hunted through the entire group of lines and

found them all busy that it will refuse to connect and will give the

busy signal to the calling subscriber.

=Party Lines.= The description of this system as given above has been

confined entirely to direct line working; however, party lines may be

and are frequently employed.

The circuits and apparatus used with direct lines are, with slight

modifications, applicable to use with party lines.

The harmonic method of ringing is employed and the stations are so

arranged with respect to the connectors that those requiring the same

frequency for ringing the bells are in groups served by the same set of

connectors.

[Illustration: POWER MACHINERY Citizens' Telephone Company, Racine, Wis.

_The Dean Electric Co._]

The party lines are operated on the principle commonly known in manual

practice as the jack per station arrangement. Each party line will,

therefore, have sets of terminals appearing in separate hundreds; the

connectors associated with each of these hundreds being so arranged as

to impress the proper frequency of ringing current on the line.

From the subscribers' standpoint the operation is the same as for direct

lines, as the particular hundreds digit of a number serves to select one

of a group of connectors capable of connecting the proper ringing

current to the line.

To avoid confusion, which would be caused by a subscriber on a party

line attempting to make a call when the line is already in use by some

other subscriber, the subscribers' stations are so arranged that when

the line is in use all other stations on the line are locked out.

[Illustration: Fig. 399. Wall Set for Two-Wire System]

=The Two-Wire Automatic System.= The two-wire system that has recently

been introduced by the Automatic Electric Company brings about the very

important result of accomplishing all of the automatic switching over

metallic circuit lines without the use of ground or common returns. The

system is thus relieved of the disturbing influences to which the

three-wire system is sometimes subjected, due to differences in earth

potential between various portions of the system, which may add to or

subtract from the battery potential and alter the net potential

available between two distant points. The introduction of this system

has also made possible certain other incidental features of advantage,

one of which is a great simplification and reduction in size of the

subscriber's station signal-transmitting apparatus.

With the doing away of the ground as a return circuit, it becomes

impossible to send vertical impulses over one side of the line and to

follow them by single rotary impulses over the other side of the line.

Yet it becomes necessary to distinguish between the pure selective

impulses and those impulses which dictate a change of function at the

central office. The plan has, therefore, been adopted of accomplishing

the selection in each case by short and rapidly recurring impulses and

of accomplishing those functions formerly brought about by the single

impulse over the rotary side of the line by a pause between the

respective series of selective impulses. This is accomplished at the

central office by replacing the vertical and the rotary relays of the

three-wire system by a quick-acting and a sluggish relay, respectively;

the quick-acting relay performing the functions previously carried out

by the vertical relay, and the sluggish relay acting only during the

pauses between the successive series of quick impulses to do the things

formerly done by the rotary relay. This has resulted in a delightful

simplification of subscriber's apparatus, since it is now necessary only

to provide a device which will connect the two sides of the line

together the required number of times in quick succession and then allow

a pause with the circuit closed while the subscriber is getting ready to

transmit another set of impulses corresponding to another digit. The

calling device has no mechanical function co-acting with any of the

other parts of the telephone and may be considered as a separate

mechanical device electrically connected with the line. The transmitting

device is not much larger than a large watch and a good idea of it may

be had from Fig. 399, which shows the latest wall set, and Fig. 400,

which shows the latest desk set of the Automatic Electric Company. We

regret the fact that this company has made the request that the complete

details of their two-wire system be not published at this time.

[Illustration: Fig. 400. Desk Stand for Two-Wire System]