_MISCELLANEOUS RECIPES._
=Oil Polish.=--One quart of cold-drawn linseed-oil to be simmered (not
boiled) for ten minutes, and strained through flannel; then add
one-eighth part of spirits of turpentine: to be applied daily with soft
linen rags, and rubbed off lightly; each time the oil is applied the
surface should be previously washed with cold water, so as to remove any
dirt or dust. This method of polishing is particularly useful for
dining-table tops; it will in about six weeks produce a polish so
durable as to resist boiling water or hot dishes, and be like a mirror
for brilliancy.
=Wax Polish.=--Eight ounces of beeswax, 2 oz. of resin, and 1/2 oz. of
Venetian turpentine, to be melted over a slow fire; the mass, when quite
melted, is poured into a sufficiently large stone-ware pot, and while it
is still warm 6 oz. of rectified turpentine are stirred in. After the
lapse of twenty-four hours the mass will have assumed the consistency
of soft butter, and is ready for use. A small portion of the polish is
taken up with a woollen rag and rubbed over the surface of the work--at
first gently, then more strongly. When the polish is uniformly laid on,
the surface is once more rubbed lightly and quickly with a fresh clean
rag to produce a gloss.
=Waterproof French Polish.=--Take 2 oz. gum benjamin, 1/2 oz. gum
sandarach, 1/2 oz. gum anîme, 11/2 oz. gum benzoin, and 1 pt. alcohol.
Mix in a closely-stoppered bottle, and put in a warm place till the gums
are well dissolved. Then strain off, and add 1/4 gill of poppy-oil.
Shake well together, and it is ready for use.
=A Varnish for Musical Instruments.=--Take one gallon of alcohol, 1 lb.
gum sandarach, 1/2 lb. gum mastic, 2 lbs. best white resin, 3 lbs. gum
benzoin; cut the gums cold. When they are thoroughly dissolved, strain
the mixture through fine muslin, and bottle for use; keep the bottle
tightly corked. This is a beautiful varnish for violins and other
musical instruments of wood, and for fancy articles, such as those of
inlaid work. It is also well adapted for panel-work, and all kinds of
cabinet furniture. There is required only one flowing coat, and it
produces a very fine mirror-like surface. Apply this varnish with a
flat camel's-hair or sable brush. In an hour after application the
surface is perfectly dry.
=French Varnish for Cabinet-work.=--Take of shellac 11/2 oz. gum mastic
and gum sandarach, of each 1/2 oz., spirit of wine by weight 20 oz. The
gums to be first dissolved in the spirit, and lastly the shellac. This
may be best effected by means of the water-bath. Place a loosely-corked
bottle containing the mixture in a vessel of warm water of a temperature
below the boiling point, and let it remain until the gums are dissolved.
Should evaporation take place, an equal quantity to the spirit of wine
so lost must be replaced till the mixture settles, then pour off the
clear liquid for use, leaving the impurities behind; but do not filter
it. Greater hardness may be given to the varnish by increasing the
quantity of shellac, which may be done to the amount of one-twelfth of
the lac to eleven-twelfths of spirit. But in this latter proportion the
varnish loses its transparency in some degree, and must be laid on in
very small quantities at a time.
=Mastic Varnish.=--Mastic should be dissolved in oil of turpentine, in
close glass vessels, by means of a gentle heat. This varnish is
extensively used in transparencies, etc.
=Cabinet-maker's Varnish.=--Take 5 lbs. very pale gum shellac, 7 oz. gum
mastic, 1 gallon alcohol. Dissolve in a cold atmosphere with frequent
stirring.
=Amber Varnish.=--This is a most difficult varnish to make. It is
usually prepared by roasting the amber and adding hot linseed-oil, after
which turpentine can be mixed if required. But for a small quantity,
dissolve the broken amber, without heat, in the smallest possible
quantity of chloroform or pure benzine. Heat the linseed-oil, remove it
from the fire, and pour in the amber solution, stirring all the time.
Then add the turpentine. If not quite clear, heat again, using the
utmost caution.
=Colourless Varnish with Copal.=--To prepare this varnish the copal must
be picked; each piece is broken, and a drop of rosemary-oil poured on
it. Those pieces which, on contact with the oil, become soft are the
ones used. The pieces being selected, they are ground and passed through
a sieve, being reduced to a fine powder. It is then placed in a glass,
and a corresponding volume of rosemary-oil poured over it; the mixture
is then stirred for a few minutes until it is transformed into a thick
liquor. It is then left to rest for two hours, when a few drops of
rectified alcohol are added, and intimately mixed. Repeat the operation
until the varnish is of a sufficient consistency; leave the rest for a
few days, and decant the clear. This varnish can be applied to wood and
metals (_Journal of Applied Chemistry_).
=Seedlac Varnish.=--Wash 3 oz. of seedlac in several waters; dry it and
powder it coarsely. Dissolve it in one pint of rectified spirits of
wine; submit it to gentle heat, shaking it as often as convenient, until
it appears dissolved. Pour off the clear part, and strain the remainder.
=Patent Varnish for Wood or Canvas.=--Take 1 gallon spirits of
turpentine, 21/4 lbs. asphaltum. Put them into an iron kettle on a
stove, and dissolve the gum by heat. When it is dissolved and a little
cool, add 1 pint copal varnish and 1 pint boiled linseed-oil. When
entirely cool it is ready for use. For a perfect black add a little
lamp-black.
=Copal Varnish.=--Dissolve the copal, broken in pieces, in linseed-oil,
by digestion, the heat being almost sufficient to boil the oil. The oil
should be made drying by the addition of quick-lime. This makes a
beautiful transparent varnish. It should be diluted with oil of
turpentine; a very small quantity of copal, in proportion to the oil,
will be found sufficient.
=Carriage Varnish.=--Take 19 oz. gum sandarach, 91/2 oz. orange
shellac, 121/2 oz. white resin, 18 oz. turpentine, 5 pints alcohol.
Dissolve and strain. Use for the internal parts of carriages and similar
purposes. This varnish dries in ten minutes.
=Transparent Varnish.=--Take 1 gallon alcohol, 2 lbs. gum sandarach, 1/2
lb. gum mastic. Place them in a tin can. Cork tight and shake
frequently, placing the can in a warm place. When dissolved it is ready
for use.
=Crystal Varnish for Maps, etc.=--Mix together 1 oz. Canada balsam and 2
oz. spirits of turpentine. Before applying this varnish to a drawing or
a painting in water-colours the paper should be placed on a stretcher,
sized with a thin solution of isinglass in water, and dried. Apply the
varnish with a soft camel's-hair brush.
=A Black Varnish.=--Mix a small quantity of gas-black with the brown
hard varnish previously mentioned. The black can be obtained by boiling
a pot over a gas-burner, so that it almost touches the burner, when a
fine jet-black will form at the bottom, which remove and mix with the
varnish, and apply with a brush.
=A Black Polish= can be made in the same way: after wetting the rubber,
just touch it with the black. Place the linen cover over, touch it with
oil, and it is ready for work.
=Varnish for Iron.=--Take 2 lbs. pulverised gum asphaltum, 1/4 lb. gum
benzoin, 1 gallon spirits of turpentine. To make this varnish quickly,
keep in a warm place, and shake often till it is dissolved. Shade to
suit with finely-ground ivory-black. Apply with a brush. This varnish
should be used on iron-work exposed to the weather. It is also well
adapted for inside work, such as iron furniture, where a handsome polish
is desired.
=Varnish for Tools.=--Take 2 oz. tallow, 1 oz. resin; melt together, and
strain while hot to remove the specks which are in the resin. Apply a
slight coat on the tools with a brush, and it will keep off the rust for
any length of time.
=To Make Labels Adhere to a Polished Surface.=--Brush the back of a
label over with thin varnish or polish, and press down with a soft rag;
this must be done quickly, as the polish soon becomes dry. This is the
way labels are put on pianofortes, and also the paper imitation of fancy
woods on polished pine-work.
=How to Remove French Polish or Varnish from Old Work.=--Cleaning off
old work for re-polishing or varnishing is usually found difficult, and
to occupy much time if only the scraper and glass-paper be used. It can
be easily accomplished in a very short time by washing the surface with
liquid ammonia, applied with a piece of rag; the polish will peel off
like a skin, and leave the wood quite bare. In carvings or turned work,
after applying the ammonia, use a hard brush to remove the varnish.
Unadulterated spirits of wine used in a tepid state will answer the same
purpose.
=Colouring for Carcase Work.=--In the best class of cabinet-work all the
inside work--such as carcase backs, shelves, etc.--is made of good
materials, such as wainscot, soft mahogany, Havannah cedar, or American
walnut; but for second-class work, pine or white deal is used instead,
and coloured.
The colouring matter used should match with the exterior wood. For
mahogany take 1/2 lb. of ground yellow ochre to a quart of water, and
add about a tablespoonful of Venetian red--a very small quantity of
red in proportion to the yellow is sufficient for mahogany--and a piece
of glue about the size of a walnut; the whole to be well stirred and
boiled. Brush over while hot, and immediately rub off with soft shavings
or a sponge. For the antique hues of old wainscot mix equal parts of
burnt umber and brown ochre. For new oak, bird's-eye maple, birch,
satin-wood, or any similar light yellowish woods, whiting or white-lead,
tinted with orange chrome, or by yellow ochre and a little size. For
walnut, brown umber, glue size, and water; or by burnt umber very
moderately modified with yellow ochre. For rosewood, Venetian red tinted
with lamp-black. For ebony, ivory-black; but for the common ebonised
work lamp-black is generally used.
When the colouring is dry, it should be rubbed down with a piece of worn
fine glass-paper, and polished with beeswax rubbed on a very hard
brush--a worn-out scrubbing-brush is as good as anything--or it can be
well rubbed with Dutch rush. In polishing always rub the way of the
grain. The cheap work seldom gets more than a coat of colour rubbed off
with shavings.
=Cheap but Valuable Stain for the Sap of Black Walnut.=--Take 1 gallon
of strong vinegar, 1 lb. dry burnt umber, 1/2 lb. fine rose-pink, 1/2
lb. dry burnt Vandyke brown. Put them into a jug and mix them well; let
the mixture stand one day, and it will then be ready for use. Apply this
stain to the sap with a piece of fine sponge; it will dry in half an
hour. The whole piece is then ready for the filling process. When
completed, the stained part cannot be detected even by those who have
performed the work. This recipe is of value, as by it wood of poor
quality and mostly of sap can be used with good effect.
=Polish for Removing Stains, etc., from Furniture (American).=--Take 1/2
pint alcohol, 1/4 oz. pulverised resin, 1/4 oz. gum shellac, 1/2 pint boiled
linseed-oil. Shake the mixture well, and apply it with a sponge, brush,
or cotton flannel, rubbing well after the application.
=Walnut Stain to be used on Pine and White-wood.=--Take 1 gallon of very
thin sized shellac; add 1 lb. of dry burnt umber, 1 lb. of dry burnt
sienna, and 1/4 lb. of lamp-black. Put these articles into a jug, and
shake frequently until they are mixed. Apply one coat with a brush. When
the work is dry, sand-paper down with fine paper, and apply one coat of
shellac or cheap varnish. It will then be a good imitation of solid
walnut, and will be adapted for the back-boards of mirror-frames, for
the backside and inside of case-work, and for similar work.
=Rosewood Stain.=--Take 1 lb. of logwood chips, 1/2 lb. of red-sanders,
1/2 gallon of water. Boil over a fire until the full strength is
obtained. Apply the mixture, while hot, to the wood with a brush. Use
one or two coats to obtain a strong red colour. Then take 1 gallon of
spirits of turpentine and 2 lb. of asphaltum. Dissolve in an iron kettle
on a stove, stirring constantly. Apply with a brush over the red stain,
to imitate rosewood. To make a perfect black, add a little lamp-black.
The addition of a small quantity of varnish with the turpentine will
improve it. This stain applied to birchwood gives as good an imitation
of rosewood as on black walnut, the shade on the birch being a little
brighter.
=Rosewood Stain for Cane Work, etc.=--Take 1 gallon alcohol, 1 lb.
red-sanders, 1 lb. dragon's blood, 1 lb. extract logwood, 1/2 lb. gum
shellac. Put the mixture into a jug, and steep well till it obtains its
full strength. Then strain, and it will be ready for use. Apply with
brush, giving one, two, or more coats, according to the depth of colour
desired. Then give one or more coats of varnish. This stain is suitable
for use on cane, willow, or reed work, and produces a good imitation of
rosewood.
=French Polish Reviver.=--This recipe will be found a valuable one. If
the work is sweated and dirty, make it tolerably wet, and let it stand a
few minutes; then rub off and polish with a soft rag. It is important
that the ingredients should be mixed in a bottle in the order as given:
Vinegar, 1 gill; methylated spirit, 1 gill; linseed-oil, 1/2 pint;
butter of antimony (poison), 1 oz. Raw linseed-oil, moderately thinned
with turpentine or spirits of wine, will also make a good reviver. Old
furniture, or furniture that has been warehoused for a long time, should
be washed with soda and warm water previous to applying the reviver.
=Morocco Leather Reviver.=--The coverings of chairs or sofas in morocco,
roan, or skiver can be much improved by this reviver. If old and greasy,
wash with sour milk first. The reviver should be applied with a piece of
wadding, and wiped one way only, as in glazing. The colour can be
matched by adding red-sanders. Methylated spirit, 1/2 pint; gum benzoin,
2 oz.; shellac, 1/2 oz. Mix, and shake up occasionally until dissolved.
=Hair-cloth Reviver.=--Mix equal parts of marrow-oil (neats-foot),
ox-gall. and ivory-black, to be well rubbed with a cloth. This
composition forms a valuable renovator for old hair-cloth.
=To Remove Grease Stains from Silks, Damasks, Cloth, etc.=--Pour over
the stain a small quantity of benzoline spirit, and it will soon
disappear without leaving the least mark behind. The most delicate
colours can be so treated without fear of injury. For paint stains
chloroform is very efficacious.
=To Remove Ink Stains from White Marble.=--Make a little chloride of
lime into a paste with water, and rub it into the stains, and let it
remain a few hours; then wash off with soap and water.