Preparation of Paper, Ink, Colour, and Paste for Printing
PAPER
The paper made by the Japanese from the inner bark of young shoots of
the mulberry and certain other plants of similar fibre is beyond all
others the best for wood-block printing. It is in itself a very
remarkable material, and is used in Japan for a great variety of
purposes, on account of the strength and toughness due to its long silky
fibre.
Paper of good quality for printing may be obtained directly from Japan,
or through trading agents dealing with Japan. A case of five reams would
be the smallest quantity obtainable directly, but it is by far the
cheapest and most satisfactory way of buying it. In smaller quantities
the paper is obtainable through many of the dealers in artists'
materials. Several kinds of this paper are made, but unsized sheets of a
quality similar to the print on page 95, and a thin Japanese tissue
paper are the two kinds required for printing in colour.
In its unsized state the paper is too absorbent for use, and it should
be sized freshly as needed for work. This is done by brushing a thin
solution of gelatine over the smooth surface of the sheets of paper.
A drawing-board rather larger than the sheets of paper, placed as shown
in fig. 17, with its lower edge resting on a basin of warm size, will be
found a convenient arrangement.
[Illustration: Plate VII. Impression of a portion of detail from a
Japanese woodblock (very nearly actual size).
(_To face page 48._)]
The sheet gelatine sold by grocers for cooking makes an excellent size.
Six of the thin sheets to a pint of water is a good strength.[3] The
gelatine is dissolved in hot water, but should not be boiled, as that
partially destroys the size. When dissolved, a little powdered alum
is also stirred in, about as much as will lie on a shilling to a pint of
water. The addition of the alum is important, as it acts as a mordant
and helps to make a better colour impression.
[3] See also p. 75.
[Illustration: FIG. 17.--Drawing of sizing of paper.]
In applying the size to the paper a four-inch broad flat paste brush is
used. The paper is laid on the slanting board and the size brushed
backward and forward across the paper from the upper end downward. Care
must be taken not to make creases in the paper, as these become
permanent. To avoid this the lower end of the sheet may be held with the
left hand and raised when necessary as the brush passes downwards. The
waste size will run down to the basin, but the paper need not be
flooded, nor should its surface be brushed unnecessarily, but it must be
fully and evenly charged with size. The sheet is then picked up by the
two upper corners (which may conveniently be kept unsized) and pinned at
each corner over a cord stretched across the workroom. The sheets are
left hanging until they are dry. The Japanese lay the paper on the
cord, letting the two halves of the sheet hang down equally on either
side.
The process of sizing and drying the sheets of paper is illustrated in a
print shown in the collection at the South Kensington Museum.
When the paper is quite dry it is taken down, and if required at once
for printing should be cut up into sheets of the size required, with
sufficient margin allowed to reach the register marks. It is best to cut
a gauge or pattern in cardboard for use in cutting the sheets to a
uniform size.
A few sheets of unsized paper are needed as damping sheets, one being
used to every three printing sheets. The damping sheets should be cut at
least an inch wider and longer than the printing sheets. Two wooden
boards are also required. The sheets of printing paper are kept between
these while damping before work.
To prepare for work, a damping sheet is taken and brushed over evenly
with water with a broad brush (like that used for sizing). The sheet
must not be soaked, but made thoroughly moist, evenly all over. It is
then laid on one of the two boards, and on it, with the printing side
(the smoother side) downward, are laid three of the sized sheets of
printing paper. On these another moist damping sheet is laid, and again
three dry sheets of printing paper, face downwards, and so on
alternately to the number of sheets of the batch to be printed. A board
is placed on the top of the pile.
The number of prints to be attempted at one printing will vary with the
kind of work and with the printer's experience. The printing may be
continued during three days, but if the paper is kept damp longer, there
is danger of mould and spotting. With work requiring delicate gradation
of colour and many separate block impressions twenty or thirty sheets
will be found sufficient for three days' hard work. The professional
printers of Japan, however, print batches of two hundred and three
hundred prints at a time, but in that case the work must become largely
mechanical.[4]
[4] See Chapter XIII for further experience on this point.
The batch of paper and damping sheets should remain between the boards
for at least half an hour when new sheets are being damped for the first
time. The damping sheets, all but the top and bottom ones, should then
be removed and the printing sheets left together between the boards for
some time before printing. An hour improves their condition very much,
the moisture spreading equally throughout the batch of sheets. Before
printing they should be quite flat and soft, but scarcely moist to the
touch. If the sheets are new, they may even be left standing all night
after the first damping, and will be in perfect condition for printing
in the morning without further damping. No weight should be placed on
the boards.
Although no paper has hitherto been found that will take so perfect an
impression from colour-blocks as the long-fibred Japanese paper, yet it
should be the aim of all craftsmen to become independent of foreign
materials as far as possible. There is no doubt that our paper-makers
should be able to produce a paper of good quality sufficiently absorbent
to take colour from the wet block and yet tough enough to bear handling
when slightly damp.
If a short-fibred paper is made without size, it comes to pieces when it
is damped for printing. But the amount of absorbency required is not so
great as to preclude the use of size altogether. It is a problem which
our paper-makers could surely solve. A soft, slightly absorbent, white
paper is required. At present nothing has been produced to take the
place of the long mulberry fibre of the Japanese, which prints
perfectly, but it is far from being pure white in colour. A white paper
would have a great advantage in printing high and delicate colour
schemes.
INK
Next in importance is the preparation of the ink for printing the
key-block or any black or grey parts of a design. As a rule the
key-block is printed black, more or less diluted with paste; indeed the
key-block is often printed very faintly by means of paste only just
tinged with a trace of black.
The use of colour for the key-block is treated in Chapter VII. The ink
is prepared as follows. Take a stick of solid Chinese ink of good
quality, and break it with a hammer into fragments; put these to soak in
a pot with water for three or four days. (The quality of the sticks of
Chinese ink varies greatly. The cheap sticks make a coarse and gritty
ink which does not print well.) Day by day pour off the water, adding
fresh, so that the glue that soaks out of the softened black fragments
is removed. Three days is usually long enough for this. If left too long
the whole mass goes bad and is spoiled. When the black mass is soft and
clean drain off the water and rub the ink smooth in a dish with a bone
palette knife. It is then ready for use, but would rapidly go bad if not
used up at once, so that a preservative is necessary to keep a stock of
ink in good condition. An effective method is to put the ink at once
into a well-corked, wide-mouthed bottle. To the under side of the cork
is nailed a little wad of unsized paper soaked with creosote. By this
means ink can be kept in perfect condition for weeks or months. A drop
of fresh creosote should occasionally be put on the wad fixed to the
cork.
[Illustration: FIG. 18.--Cork of ink-bottle with wad for
preservative.]
Fresh ink may at any time be obtained rapidly in small quantities by
rubbing down a stick of Chinese ink on a slab in the ordinary way, but
this is very laborious, and is only worth while if one needs a small
quantity of a glossy black, for which the rubbed-down ink containing all
its glue is the best.
COLOUR
Any colour that can be obtained in a fine dry powder may be used in
wood-block printing. Some artists have succeeded in using ordinary
water colours sold in tubes, by mixing the colour with the rice paste
before printing; but the best results are obtained by the use of pure,
finely ground dry colour mixed only with water, the rice paste being
added actually on the block.
Most of the artists' colour merchants supply colour by weight in the
form of dry powder: any colour that is commonly used in oil or
water-colour painting may be obtained in this state. A stock of useful
colours should be kept in wide-necked bottles.
A few shallow plates or small dishes are needed to hold colour and a
bone or horn palette knife for mixing and rubbing the colour into a
smooth paste in the dishes. Small bone paper knives are useful for
taking colour from the bottles.
When the colour scheme of a print is made certain--and this is best done
by printing small experimental batches--it is a good plan to have a
number of covered pots equal to the number of the different colour
impressions, and to fill these with a quantity of each tint, the colour
or colours being mixed smoothly with water to the consistency of stiff
cream.
Some colours will be found to print more smoothly and easily than
others. Yellow ochre, for instance, prints with perfect smoothness and
ease, while heavier or more gritty colours tend to separate and are more
difficult. In the case of a very heavy colour such as vermilion, a drop
of glue solution will keep the colour smooth for printing, and less
paste is necessary. But most colours will give good impressions by means
of rice paste alone. It is essential, however, that only very finely
ground colours of good quality should be used.
PASTE
A paste must be used with the colour in order to hold it on to the
surface of the paper and to give brilliancy. The colour, if printed
without paste, would dry to powder again. The paste also preserves the
matt quality which is characteristic of the Japanese prints.
Finely ground rice flour may be obtained from grocery dealers. An
excellent French preparation of rice sold in packets as _Crême de Riz_
is perfect for the purpose of making paste for printing. It should be
carefully made as follows: While half a pint of water is put to boil in
a saucepan over a small spirit lamp or gas burner, mix in a cup about
two teaspoonfuls of rice flour with water, added little by little until
a smooth cream is made with no lumps in it. A bone spoon is good for
this purpose. Pour this mixture into the boiling water in the saucepan
all at once, and stir well till it boils again, after which it should be
left simmering over a small flame for five minutes.
When the paste has cooled it should be smooth and almost fluid enough to
pour: not stiff like a pudding.
While printing, a little paste is put out in a saucer and replenished
from time to time.
Fresh paste should be made every day.