SIMPLE TELEGRAPH AND TELEPHONE RECEIVING SETS
With a crystal detector receiving set you can receive either
telegraphic dots and dashes or telephonic speech and music. You can
buy a receiving set already assembled or you can buy the different
parts and assemble them yourself. An assembled set is less bother in
the beginning but if you like to experiment you can _hook up_, that
is, connect the separate parts together yourself and it is perhaps a
little cheaper to do it this way. Then again, by so doing you get a
lot of valuable experience in wireless work and an understanding of
the workings of wireless that you cannot get in any other way.
Assembled Wireless Receiving Sets.--The cheapest assembled receiving
set [Footnote: The Marvel, made by the Radio Mfg. Co., New York City.]
advertised is one in which the detector and tuning coil is mounted in
a box. It costs $15.00, and can be bought of dealers in electric
supplies generally.
This price also includes a crystal detector, an adjustable tuning
coil, a single telephone receiver with head-band and the wire,
porcelain insulators, lightning switch and ground clamp for the aerial
wire system. It will receive wireless telegraph and telephone messages
over a range of from 10 to 25 miles.
Another cheap unit receptor, that is, a complete wireless receiving
set already mounted which can be used with a single aerial is sold for
$25.00. [Footnote: The Aeriola Jr., made by the Westinghouse Company,
Pittsburgh, Pa.] This set includes a crystal detector, a variable
tuning coil, a fixed condenser and a pair of head telephone receivers.
It can also be used to receive either telegraph or telephone messages
from distances up to 25 miles. The aerial equipment is not included in
this price, but it can be bought for about $2.50 extra.
Assembling Your Own Receiving Set.--In this chapter we shall go only
into the apparatus used for two simple receiving sets, both of which
have a _crystal detector_. The first set includes a _double-slide
tuning coil_ and the second set employs a _loose-coupled tuning coil_,
or _loose coupler_, as it is called for short. For either set you can
use a pair of 2,000- or 3,000-ohm head phones.
[Illustration: original © Underwood and Underwood. General Pershing
Listening In.]
The Crystal Detector.--A crystal detector consists of: (1) _the
frame_, (2) _the crystal_, and (3) _the wire point_. There are any
number of different designs for frames, the idea being to provide a
device that will (a) hold the sensitive crystal firmly in place, and
yet permit of its removal, (b) to permit the _wire point_, or
_electrode_, to be moved in any direction so that the free point of it
can make contact with the most sensitive spot on the crystal and (c)
to vary the pressure of the wire on the crystal.
A simple detector frame is shown in the cross-section at A in Fig. 10;
the crystal, which may be _galena_, _silicon_ or _iron pyrites_, is
held securely in a holder while the _phosphor-bronze wire point_ which
makes contact with it, is fixed to one end of a threaded rod on the
other end of which is a knob. This rod screws into and through a
sleeve fixed to a ball that sets between two brass standards and this
permits an up and down or a side to side adjustment of the metal point
while the pressure of it on the crystal is regulated by the screw.
[Illustration: (A) Fig. 10.--Cross Section of Crystal Detector.]
[Illustration: (B) Fig. 10.--The Crystal Detector Complete.]
A crystal of this kind is often enclosed in a glass cylinder and this
makes it retain its sensitiveness for a much longer time than if it
were exposed to dust and moisture. An upright type of this detector
can be bought for $2.25, while a horizontal type, as shown at B, can
be bought for $2.75. Galena is the crystal that is generally used,
for, while it is not quite as sensitive as silicon and iron pyrites,
it is easier to obtain a sensitive piece.
The Tuning Coil.--It is with the tuning coil that you _tune in_ and
_tune out_ different stations and this you do by sliding the contacts
to and fro over the turns of wire; in this way you vary the
_inductance_ and _capacitance_, that is, the _constants_ of the
receiving circuits and so make them receive _electric waves_, that is,
wireless waves, of different lengths.
The Double Slide Tuning Coil.--With this tuning coil you can receive
waves from any station up to 1,000 meters in length. One of the ends
of the coil of wire connects with the binding post marked _a_ in Fig.
11, and the other end connects with the other binding post marked _b_,
while one of the sliding contacts is connected to the binding post
_c_, and the _other sliding contact_ is connected with the binding
post _d_.
[Illustration: (A) Fig. 11.--Schematic Diagram of Double Slide Tuning
Coil.]
[Illustration: (B) Fig. 11.--Double Slide Tuning Coil Complete.]
When connecting in the tuning coil, only the post _a_ or the post _b_
is used as may be most convenient, but the other end of the wire which
is connected to a post is left free; just bear this point in mind when
you come to connect the tuning coil up with the other parts of your
receiving set. The tuning coil is shown complete at B and it costs
$3.00 or $4.00. A _triple slide_ tuning coil constructed like the
double slide tuner just described, only with more turns of wire on it,
makes it possible to receive wave lengths up to 1,500 meters. It costs
about $6.00.
The Loose Coupled Tuning Coil.--With a _loose coupler_, as this kind
of a tuning coil is called for short, very _selective tuning_ is
possible, which means that you can tune in a station very sharply, and
it will receive any wave lengths according to size of coils. The
primary coil is wound on a fixed cylinder and its inductance is varied
by means of a sliding contact like the double slide tuning coil
described above. The secondary coil is wound on a cylinder that slides
in and out of the primary coil. The inductance of this coil is varied
by means of a switch that makes contact with the fixed points, each of
which is connected with every twentieth turn of wire as shown in the
diagram A in Fig. 12. The loose coupler, which is shown complete at B,
costs in the neighborhood of $8.00 or $10.00.
[Illustration: (A) Fig. 12.--Schematic Diagram of Loose Coupler.]
[Illustration: (B) Fig. 12.--Loose Coupler Complete.]
Fixed and Variable Condensers.--You do not require a condenser for a
simple receiving set, but if you will connect a _fixed condenser_
across your headphones you will get better results, while a _variable
condenser_ connected in the _closed circuit of a direct coupled
receiving set_, that is, one where a double slide tuning coil is used,
makes it easy to tune very much more sharply; a variable condenser is
absolutely necessary where the circuits are _inductively coupled_,
that is, where a loose coupled tuner is used.
A fixed condenser consists of a number of sheets of paper with leaves
of tin-foil in between them and so built up that one end of every
other leaf of tin-foil projects from the opposite end of the paper as
shown at A in Fig. 13. The paper and tin-foil are then pressed
together and impregnated with an insulating compound. A fixed
condenser of the exact capacitance required for connecting across the
head phones is mounted in a base fitted with binding posts, as shown
at B, and costs 75 cents. (Paper ones 25 cents.)
[Illustration: (A) Fig. 13.--How a Fixed Receiving Condenser is Built
up.]
[Illustration: (B) Fig. 13.--The Fixed Condenser Complete.]
[Illustration: (C) and (D) Fig. 13.--The Variable Rotary Condenser.]
A variable condenser, see C, of the rotating type is formed of a set
of fixed semi-circular metal plates which are slightly separated from
each other and between these a similar set of movable semi-circular
metal plates is made to interleave; the latter are secured to a shaft
on the top end of which is a knob and by turning it the capacitance of
the condenser, and, hence, of the circuit in which it is connected, is
varied. This condenser, which is shown at D, is made in two sizes, the
smaller one being large enough for all ordinary wave lengths while the
larger one is for proportionately longer wave lengths. These
condensers cost $4.00 and $5.00 respectively.
About Telephone Receivers.--There are a number of makes of head
telephone receivers on the market that are designed especially for
wireless work. These phones are wound to _resistances_ of from 75
_ohms_ to 8,000 _ohms_, and cost from $1.25 for a receiver
without a cord or headband to $15.00 for a pair of phones with a cord
and head band. You can get a receiver wound to any resistance in
between the above values but for either of the simple receiving sets
such as described in this chapter you ought to have a pair wound to at
least 2,000 ohms and these will cost you about $5.00. A pair of head
phones of this type is shown in Fig. 14.
[Illustration: Fig. 14.--Pair of Wireless Head Phones.]
Connecting Up the Parts--Receiving Set No. 1.--For this set get (1) a
_crystal detector_, (2) a _two-slide tuning coil_, (3) a _fixed
condenser_, and (4) a pair of 2,000 ohm head phones. Mount the
detector on the right-hand side of a board and the tuning coil on the
left-hand side. Screw in two binding posts for the cord ends of the
telephone receivers at _a_ and _b_ as shown at A in Fig. 15. This done
connect one of the end binding posts of the tuning coil with the
ground wire and a post of one of the contact slides with the lightning
arrester or switch which leads to the aerial wire.
[Illustration: Fig. 15.--Top View of Apparatus Layout for Receiving
Set No. 1.]
[Illustration: (B) Fig. 15.--Wiring Diagram for Receiving Set No. 1.]
Now connect the post of the other contact slide to one of the posts of
the detector and the other post of the latter with the binding post
_a_, then connect the binding post _b_ to the ground wire and solder
the joint. Next connect the ends of the telephone receiver cord to the
posts _a_ and _b_ and connect a fixed condenser also with these posts,
all of which are shown in the wiring diagram at B, and you are ready
to adjust the set for receiving.
Receiving Set No. 2.--Use the same kind of a detector and pair of head
phones as for _Set No. 1_, but get (1) a _loose coupled tuning coil_,
and (2) a _variable condenser_. Mount the loose coupler at the back of
a board on the left-hand side and the variable condenser on the
right-hand side. Then mount the detector in front of the variable
condenser and screw two binding posts, _a_ and _b_, in front of the
tuning coil as shown at A in Fig. 16.
[Illustration: Fig. 16.--Top view of Apparatus Layout for Receiving
Set No. 2.]
[Illustration: (B) Fig. 16.--Wiring Diagram for Receiving Set No. 2.]
Now connect the post of the sliding contact of the loose coupler with
the wire that runs to the lightning switch and thence to the aerial;
connect the post of the primary coil, which is the outside coil, with
the ground wire; then connect the binding post leading to the switch
of the secondary coil, which is the inside coil, with one of the posts
of the variable condenser, and finally, connect the post that is
joined to one end of the secondary coil with the other post of the
variable condenser.
This done, connect one of the posts of the condenser with one of the
posts of the detector, the other post of the detector with the binding
post _a_, and the post _b_ to the other post of the variable
condenser. Next connect a fixed condenser to the binding posts _a_ and
_b_ and then connect the telephone receivers to these same posts, all
of which is shown in the wiring diagram at B. You are now ready to
adjust the instruments. In making the connections use No. 16 or 18
insulated copper wire and scrape the ends clean where they go into the
binding posts. See, also, that all of the connections are tight and
where you have to cross the wires keep them apart by an inch or so and
always cross them at right angles.
Adjusting the No. 1 Set--The Detector.--The first thing to do is to
test the detector in order to find out if the point of the contact
wire is on a sensitive spot of the crystal. To do this you need a
_buzzer_, a _switch_ and a _dry cell_. An electric bell from which the
gong has been removed will do for the buzzer, but you can get one that
is made specially for the purpose, for 75 cents, which gives out a
clear, high-pitched note that sounds like a high-power station.
Connect one of the binding posts of the buzzer with one post of the
switch, the other post of the latter with the zinc post of the dry
cell and the carbon post of this to the other post of the buzzer. Then
connect the post of the buzzer that is joined to the vibrator, to the
ground wire as shown in the wiring diagram, Fig. 17. Now close the
switch of the buzzer circuit, put on your head phones, and move the
wire point of the detector to various spots on the crystal until you
hear the sparks made by the buzzer in your phones.
[Illustration: Fig. 17.--Adjusting the Receiving Set.]
Then vary the pressure of the point on the crystal until you hear the
sparks as loud as possible. After you have made the adjustment open
the switch and disconnect the buzzer wire from the ground wire of your
set. This done, be very careful not to jar the detector or you will
throw it out of adjustment and then you will have to do it all over
again. You are now ready to tune the set with the tuning coil and
listen in.
The Tuning Coil.--To tune this set move the slide A of the
double-slide tuner, see B in Fig. 15, over to the end of the coil that
is connected with the ground wire and the slide B near the opposite
end of the coil, that is, the one that has the free end. Now move the
slide A toward the B slide and when you hear the dots and dashes, or
speech or music, that is coming in as loud as you can move the B slide
toward the A slide until you hear still more loudly. A very few trials
on your part and you will be able to tune in or tune out any station
you can hear, if not too close or powerful.
[Illustration: original © Underwood and Underwood. The World's
Largest Radio Receiving Station. Owned by the Radio Corporation of
America at Rocky Point near Point Jefferson, L.I.]
Adjusting the No. 2 Set.--First adjust the crystal detector with the
buzzer set as described above with _Set No. 1,_ then turn the knob of
your variable condenser so that the movable plates are just half-way
in, pull the secondary coil of your loose-coupled tuner half way out;
turn the switch lever on it until it makes a contact with the middle
contact point and set the slider of the primary coil half way between
the ends.
Now listen in for telegraphic signals or telephonic speech or music;
when you hear one or the other slide the secondary coil in and out of
the primary coil until the sounds are loudest; now move the contact
switch over the points forth and back until the sounds are still
louder, then move the slider to and fro until the sounds are yet
louder and, finally, turn the knob of the condenser until the sounds
are clear and crisp. When you have done all of these things you have,
in the parlance of the wireless operator, _tuned in_ and you are ready
to receive whatever is being sent.