_TEXTILE CALCULATIONS_
The numbers of cotton yarns are based upon the hank of 840 yards, the
number of hanks in 1 lb. being the “counts.”
It follows that if 840--the yards in one hank--be multiplied by the
counts, the result will be the yards in 1 lb. of that count.
Thus in 1 lb. of 30’s yarn there will be 840 × 30 = 25,200 yards, and
the yards in a pound of any count may be found in the same manner.
The counts of worsted yarns are based upon a hank of 560 yards, and the
number of hanks in 1 lb. Avoirdupois is the count of the yarn.
Linen yarns are based on a hank or lea of 300 yards, and the number of
these in 1 lb. is the count of the yarn.
Spun silk, which is the silk chiefly used in cotton fabrics for stripes
and headings, is numbered on the same system as cotton yarns. The
number of hanks of 840 yards in 1 lb. is the count of the yarn.
Net silks or thrown silks are numbered on an altogether different
system. The “skein” or hank is 520 yards, and the number of
deniers--533⅓ deniers = 1 oz.--which a skein weighs indicates the
number of the yarn. In silk manufacture the number of the yarn is
called the “size,” the word “count” being used to denote the closeness
of the reed.
Another system is used for silk yarns called the Manchester scale. This
is based upon the hank of 1,000 yards.
The number of drams which one such hank weighs is the “size” or number
of the yarn or thread.
In the former scale the yards per ounce may be found by multiplying the
yards in a hank by the deniers in one ounce, and dividing by the number
of deniers which a hank weighs.
The yards in an ounce of 40 denier silk will be--
deniers per oz. yards in skein
(533⅓ × 520)
--------------------- = 6933⅓ yards per oz.
40 deniers
In the Manchester silk scale the yards per ounce of a 4 dram silk may
be found by multiplying 1,000, the yards in a hank, by 16, the drams in
an ounce, and dividing by the number of drams which the hank weighs,
viz. 4; thus--
(1000 × 16)
----------- = 4000 yards per oz.
4
=Twofold Yarns= in cotton, worsted, and linen are numbered
according to the count of the single yarn, with the number of folds put
before it. Thus a 2-40’s yarn means that the yarn is composed of two
threads of 40’s single, making a twofold yarn of 20 hanks to the pound.
In spun silk the yarns are nearly always two or more fold, and the
number of the yarn always indicates the number of hanks in 1 lb. The
number of folds is usually written after the hanks per pound. Thus,
40’s-2 spun silk indicates that the yarn is 40 hanks to the pound, made
up of two threads of 80’s single.
It sometimes occurs in fancy yarns that threads of unequal thickness
are twisted together. If a 60’s thread and a 40’s thread are twisted
together, the count of the doubled thread will not be the same as if
two threads of 50 hanks to the pound, but will be something less than
this.
It is obvious that when the two threads are twisted together the
weight of a hank of the doubled thread will be 1/60 + 1/40 of a pound,
and by adding these fractions together the counts of the twofold yarn
may be obtained. Thus--
1 1 (3 + 2) 5
-- + -- = ------- = --- = 24’s counts.
40 60 120 120
Another method of obtaining the same result is to multiply the two
numbers together, and add them together, and divide one result by the
other. Thus--
60 60
40 40
--- ----
100) 2400 (24’s counts.
2400
----
If three or more unequal threads are twisted together the counts of the
resulting thread may be found by adding the fractions of a pound which
a hank of each count represents.
_Example._--Find the counts of a threefold thread composed of one
thread each of 10’s, 20’s and 60’s cotton.
1 1 1 (6 + 3 +1) 10 1
-- + -- + -- = ---------- = -- = -- or 6’s counts.
10 20 60 60 60 6
Some allowance must be made for the twisting of the threads, but this
will vary with the number of turns per inch in the yarn, and so is not
taken into account in the example.
If it is required to obtain the weight of each count in 100 lbs. of the
threefold yarn, the following is the method.
As one count is to the resulting count, so is the total weight to the
weight required of that yarn--
10 : 6 ∷ 100 : 60 lbs. of 10’s
20 : 6 ∷ 100 : 30 lbs. of 20’s
60 : 6 ∷ 100 : 10 lbs. of 60’s
----
100 lbs. Total.
=Reeds and Setts.=--The system of numbering reeds, now almost
universal in the cotton trade, is known as the Stockport or Manchester
count. The number of dents or splits per inch in the reed with two ends
in each dent is the basis of the system. If the reed has 30 dents per
inch, it is called a 60 reed, because if there are two ends in a dent
in the 30 dents there will be 60 ends per inch. The number of the reed
is always the same as the ends per inch in the reed, if the ends are
all two in a dent.
A 60 reed Stockport counts, if reeded three ends in a dent, will have
90 ends per inch, because a 60 reed has 30 dents per inch, and if there
are three in a dent, there will be 30 × 3 = 90 ends per inch.
Various other systems have been used, but are gradually giving way to
the simpler Stockport or Manchester system. Some of these are--
The Bolton count, in which the number of “beers” of 40 ends, or 20
dents, in 24¼ inches is the basis of the system.
The Blackburn count, in which the number of beers in 45 inches was the
basis. The beer, as above, being 20 dents, representing 40 ends in a
beer.
The Preston count was based on the number of beers in different widths.
The 6-4 count was based on the number of beers of 20
dents--representing 40 ends--in 58 inches.
The 9-8’s count was based on the number of beers in 44 inches.
The 4-4’s count was based on the beers in 39 inches.
The 7-8’s count was based on the beers in 34 inches.
The Scotch system is based on the number of dents in 37 inches. Thus in
a 2000 reed there will be 2000 dents in 37 inches, representing 4000
ends in that space.
The Bradford system is based on the number of beers of 40 ends in 36
inches. If there are 50 times 40 ends in 36 inches, it is a “50 sett.”
To find the number of ends per inch in a given sett, it is necessary to
multiply the sett by 40 and divide by 36, thus--
(50 sett × 40)
-------------- = 55-20/36 ends per inch.
36
=Quantity of Material in a Piece.=--To find the weight of warp and
weft of given counts in a piece, the total length of yarn in the piece
may be found, and divided by the yards in 1 lb. of the counts of yarn
used. This will give the weight in pounds. The following example will
make the principle quite clear:--
_Example._--Find the weight of warp and weft in a piece woven 30
inches wide in a 70 reed (Stockport) cloth 90 yards long, from 95
yards of warp, 80 picks per inch, the counts of twist or warp being
30’s, and counts of weft 40’s.
If the piece is 90 yards long, the length of warp used will be somewhat
in excess of this, as the warp in interlacing with the weft is bent out
of a straight line. The amount of “milling up,” as it is called, varies
according to the number of intersections in the pattern or weave of the
cloth, and with the counts of yarn used. It will also vary considerably
according to the elasticity of the yarn. Twofold yarns are more elastic
than single, and therefore will require a shorter length of yarn for a
given length of cloth.
In this example 95 yards of warp are used to weave a 90-yards piece, an
allowance of a little over 5 per cent.
In making the calculation for the weft it is necessary to take the
width in the reed, as this length of weft is used every pick. The cloth
will contract a little owing to the pull of the threads when woven,
and when calculating for a given width of cloth care must be taken to
calculate for the reed width and not the cloth width only.
In the present example the width in the reed is given, and so the cloth
will be somewhat narrower than this when woven.
TO FIND WEIGHT OF WARP.
840 yards in 1 hank 70 ends per inch
30 counts 30 inches in reed
----- ----
25200 yards in 1 lb. 2100 ends in warp
95 yards long
-----
10500
18900
------
199500 yards of twist in piece.
yards
199500
Therefore, weight of warp = ----- = 7 lbs. 14⅔ oz.
25200
yds. in 1 lb.
TO FIND WEIGHT OF WEFT.
840 yards in 1 hank 80 picks per inch
40 30 inches in reed
----- ----
33600 yards in 1 lb. 2400 inches of weft in 1 inch of cloth
36 inches in 1 yard
-----
14400
7200
-----
36)86400 inches of weft in 1 yard of cloth
-----
2400 yards of weft in 1 yard of cloth
90 yards length of piece
----
216000 yards of weft in piece.
216000
Therefore, weight of weft = ------ = 6 lbs. 6-6/7 oz.
33600
Weight of weft = 6 lbs. 6-6/7 oz.
Weight of warp = 7 lbs. 14⅔ oz.
In the weft calculation, the picks per inch multiplied by the width in
the reed in inches gives the inches of weft in one inch of cloth. This
multiplied by 36 will give the inches of weft in one yard of cloth, and
divided by 36, this gives the yards of weft in one yard of cloth. The
two 36’s may be left out, as it is obvious that the yards of weft in a
yard of cloth are the same as the inches of weft in an inch of cloth.
The formula to calculate the weight of warp in a piece is as follows:--
Inches in reed × length of warp in yards × ends per inch in reed
----------------------------------------------------------------
840 × counts
= =weight of warp=.
The formula for the weft is--
Inches in reed × length of piece in yards × picks per inch
----------------------------------------------------------
840 × counts
= =weight of weft=.
Working out the previous calculation in this manner, we get--
30 × 95 × 70
------------ = 7 lbs. 14⅔ oz. of warp.
840 × 30
30 × 90 × 80
------------ = 6 lbs. 6-6/7 oz. of weft.
840 × 40
If it is required to find the number of hanks, it is only necessary to
leave out the counts in the above formulæ. Thus we get--
Inches wide × length × ends per inch
------------------------------------ = hanks,
840
and using the figures in the previous example--
30 × 95 × 70
------------ = 237½ hanks of warp.
840
Before the actual cost of a piece of cloth can be calculated, it is
necessary to know the price to be paid the weaver. In Lancashire the
payment is made according to the list agreed upon by both employers
and employed. For plain cloths and twills a new uniform list has been
agreed upon, and this is now generally accepted. The following is the
new list:--
UNIFORM LIST OF PRICES FOR WEAVING.
=1. The Standard.=--The standard upon which this list is based is
an ordinary loom, 45 inches reed space, measured from the fork grate on
one side to the back board on the other, weaving cloth as follows:--
Width: 39, 40, 41 inches.
Reed: 60 reed, 2 ends in a dent, or 60 ends per inch.
Picks: 15 picks per quarter-inch, ascertained by arithmetical
calculation, with 1½ per cent. added for contraction.
Length: 100 yards, 36 inches to the yard, measured on the counter. Any
length of lap other than 36 inches to be paid in proportion.
Twist: 28’s, or any finer numbers.
Weft: 31’s to 100’s inclusive.
Price 2_s_. 6_d_., or 2_d_. per pick, per quarter-inch.
=2. Width of Looms.=--A 45-inch reed space loom being taken as the
standard, 1½ per cent. shall be added for each inch up to and including
51 inches; 2 per cent. from 51 to 56 inches; 2½ per cent. from 56 to 64
inches; and 3 per cent. from 64 to 72 inches.
1¼ per cent. shall be deducted for each inch from 45 to 37 inches
inclusive, and 1 per cent. from 37 to 24 inches, below which no further
deduction shall be made. For any fraction of an inch up to the half no
addition or deduction shall be made; but if over the half, the same
shall be paid as if it were a full inch.
All additions or deductions under this clause to be added to, or taken
from, the price of the standard loom 45 inches.
DEDUCTED FROM STANDARD.
+---------+-----------+
| Loom. |Percentage.|
+---------+-----------+
| Inches. | |
| 24 | 23 |
| 25 | 22 |
| 26 | 21 |
| 27 | 20 |
| 28 | 19 |
| 29 | 18 |
| 30 | 17 |
| 31 | 16 |
| 32 | 15 |
| 33 | 14 |
| 34 | 13 |
| 35 | 12 |
| 36 | 11 |
| 37 | 10 |
| 38 | 8¾ |
| 39 | 7½ |
| 40 | 6¼ |
| 41 | 5 |
| 42 | 3¾ |
| 43 | 2½ |
| 44 | 1¼ |
| 45 | standard |
+---------+-----------+
ADDED TO STANDARD.
+---------+-----------+
| Loom. |Percentage.|
+---------+-----------+
| Inches. | |
| 46 | 1½ |
| 47 | 3 |
| 48 | 4½ |
| 49 | 6 |
| 50 | 7½ |
| 51 | 9 |
| 52 | 11 |
| 53 | 13 |
| 54 | 15 |
| 55 | 17 |
| 56 | 19 |
| 57 | 21½ |
| 58 | 24 |
| 59 | 26½ |
| 60 | 29 |
| 61 | 31½ |
| 62 | 34 |
| 63 | 36½ |
| 64 | 39 |
| 65 | 42 |
| 66 | 45 |
| 67 | 48 |
| 68 | 51 |
| 69 | 54 |
| 70 | 57 |
| 71 | 60 |
| 72 | 63 |
+---------+-----------+
=3. Broader Cloth than admitted by Rule.=--All looms shall be
allowed to weave to within 4 inches of the reed space; but whenever the
difference between the width of cloth and the reed space is less than
4 inches, it shall be paid as if the loom were 1 inch broader: and if
less than 3 inches, as if it were 2½ inches broader.
=4. Allowance for Cloth 7 to 15 inches narrower than the Reed
Space.=--When the cloth is from 7 to 15 inches narrower than the
reed space of the loom in which it is woven, a deduction in accordance
with the following table shall be made:--
DEDUCTIONS FOR NARROW CLOTH.
+------+------+-------+
|Reed |Cloth.| Per |
|space.| | cent. |
+------+------+-------+
| 72 | 65 | 1·38 |
| 72 | 64 | 2·76 |
| 72 | 63 | 4·14 |
| 72 | 62 | 5·52 |
| 72 | 61 | 6·9 |
| 72 | 60 | 8·28 |
| 72 | 59 | 9·66 |
| 72 | 58 | 11·04 |
| 72 | 57 | 12·19 |
| 71 | 64 | 1·41 |
| 71 | 63 | 2·81 |
| 71 | 62 | 4·22 |
| 71 | 61 | 5·62 |
| 71 | 60 | 7·03 |
| 71 | 59 | 8·44 |
| 71 | 58 | 9·84 |
| 71 | 57 | 11·02 |
| 71 | 56 | 12·19 |
| 70 | 63 | 1·43 |
| 70 | 62 | 2·87 |
| 70 | 61 | 4·3 |
| 70 | 60 | 5·73 |
| 70 | 59 | 7·17 |
| 70 | 58 | 8·6 |
| 70 | 57 | 9·79 |
| 70 | 56 | 10·99 |
| 70 | 55 | 12·18 |
| 69 | 62 | 1·46 |
| 69 | 61 | 2·92 |
| 69 | 60 | 4·38 |
| 69 | 59 | 5·84 |
| 69 | 58 | 7·31 |
| 69 | 57 | 8·52 |
| 69 | 56 | 9·74 |
| 69 | 55 | 10·96 |
| 69 | 54 | 12·18 |
| 68 | 61 | 1·49 |
| 68 | 60 | 2·98 |
| 68 | 59 | 4·47 |
| 68 | 58 | 5·96 |
| 68 | 57 | 7·2 |
| 68 | 56 | 8·44 |
| 68 | 55 | 9·69 |
| 68 | 54 | 10·93 |
| 68 | 53 | 12·17 |
| 67 | 60 | 1·52 |
| 67 | 59 | 3·04 |
| 67 | 58 | 4·56 |
| 67 | 57 | 5·83 |
| 67 | 56 | 7·09 |
| 67 | 55 | 8·36 |
| 67 | 54 | 9·63 |
| 67 | 53 | 10·9 |
| 67 | 52 | 12·16 |
| 66 | 59 | 1·55 |
| 66 | 58 | 3·1 |
| 66 | 56 | 5·69 |
| 66 | 55 | 6·98 |
| 66 | 54 | 8·28 |
| 66 | 53 | 9·57 |
| 66 | 52 | 10·86 |
| 66 | 51 | 12·16 |
| 65 | 58 | 1·58 |
| 65 | 57 | 2·91 |
| 65 | 56 | 4·23 |
| 65 | 55 | 5·55 |
| 65 | 54 | 6·87 |
| 65 | 53 | 8·19 |
| 65 | 52 | 9·51 |
| 65 | 51 | 10·83 |
| 65 | 50 | 12·15 |
| 64 | 57 | 1·35 |
| 64 | 56 | 2·7 |
| 64 | 55 | 4·05 |
| 64 | 54 | 5·4 |
| 64 | 53 | 6·74 |
| 64 | 52 | 8·09 |
| 64 | 51 | 9·44 |
| 64 | 50 | 10·79 |
| 64 | 49 | 11·87 |
| 63 | 56 | 1·37 |
| 63 | 55 | 2·75 |
| 63 | 54 | 4·12 |
| 63 | 53 | 5·49 |
| 63 | 52 | 6·87 |
| 63 | 51 | 8·24 |
| 63 | 50 | 9·62 |
| 63 | 49 | 10·71 |
| 63 | 48 | 11·81 |
| 62 | 55 | 1·4 |
| 62 | 54 | 2·8 |
| 62 | 53 | 4·2 |
| 62 | 52 | 5·6 |
| 62 | 51 | 7·0 |
| 62 | 50 | 8·4 |
| 62 | 49 | 9·51 |
| 62 | 47 | 11·75 |
| 61 | 54 | 1·43 |
| 61 | 53 | 2·85 |
| 61 | 52 | 4·28 |
| 61 | 51 | 5·7 |
| 61 | 50 | 7·13 |
| 61 | 49 | 8·27 |
| 61 | 48 | 9·41 |
| 61 | 47 | 10·55 |
| 61 | 46 | 11·69 |
| 60 | 53 | 1·45 |
| 60 | 52 | 2·91 |
| 60 | 51 | 4·36 |
| 60 | 50 | 5·81 |
| 60 | 49 | 6·98 |
| 60 | 48 | 8·14 |
| 60 | 47 | 9·3 |
| 60 | 46 | 10·47 |
| 60 | 45 | 11·63 |
| 59 | 52 | 1·48 |
| 59 | 51 | 2·96 |
| 59 | 50 | 4·45 |
| 59 | 49 | 5·63 |
| 59 | 48 | 6·82 |
| 59 | 47 | 8·0 |
| 59 | 46 | 9·19 |
| 59 | 45 | 10·38 |
| 59 | 44 | 11·26 |
| 58 | 51 | 1·51 |
| 58 | 50 | 3·02 |
| 58 | 49 | 4·23 |
| 58 | 48 | 5·44 |
| 58 | 47 | 6·65 |
| 58 | 46 | 7·86 |
| 58 | 45 | 9·07 |
| 58 | 44 | 9·98 |
| 58 | 43 | 10·89 |
| 57 | 50 | 1·54 |
| 57 | 49 | 2·78 |
| 57 | 48 | 4·01 |
| 57 | 47 | 5·25 |
| 57 | 46 | 6·48 |
| 57 | 45 | 7·72 |
| 57 | 44 | 8·64 |
| 57 | 43 | 9·57 |
| 57 | 42 | 10·49 |
| 56 | 49 | 1·26 |
| 56 | 48 | 2·52 |
| 56 | 47 | 3·78 |
| 56 | 46 | 5·04 |
| 56 | 45 | 6·3 |
| 56 | 44 | 7·25 |
| 56 | 43 | 8·19 |
| 56 | 42 | 9·14 |
| 56 | 41 | 10·08 |
| 55 | 48 | 1·28 |
| 55 | 47 | 2·56 |
| 55 | 46 | 3·85 |
| 55 | 45 | 5·13 |
| 55 | 44 | 6·09 |
| 55 | 43 | 7·05 |
| 55 | 42 | 8·01 |
| 55 | 41 | 8·97 |
| 55 | 40 | 9·94 |
| 54 | 47 | 1·3 |
| 54 | 46 | 2·61 |
| 54 | 45 | 3·91 |
| 54 | 44 | 4·89 |
| 54 | 43 | 5·87 |
| 54 | 42 | 6·85 |
| 54 | 41 | 7·83 |
| 54 | 40 | 8·8 |
| 54 | 39 | 9·78 |
| 53 | 46 | 1·33 |
| 53 | 45 | 2·65 |
| 53 | 44 | 3·65 |
| 53 | 43 | 4·65 |
| 53 | 42 | 5·64 |
| 53 | 41 | 6·64 |
| 53 | 40 | 7·63 |
| 53 | 39 | 8·63 |
| 53 | 38 | 9·42 |
| 52 | 45 | 1·35 |
| 52 | 44 | 2·36 |
| 52 | 43 | 3·38 |
| 52 | 42 | 4·39 |
| 52 | 41 | 5·41 |
| 52 | 40 | 6·42 |
| 52 | 39 | 7·43 |
| 52 | 38 | 8·28 |
| 52 | 37 | 9·12 |
| 51 | 44 | 1·03 |
| 51 | 43 | 2·06 |
| 51 | 42 | 3·1 |
| 51 | 41 | 4·13 |
| 51 | 40 | 5·16 |
| 51 | 39 | 6·19 |
| 51 | 38 | 7·05 |
| 51 | 37 | 7·91 |
| 51 | 36 | 8·77 |
| 50 | 43 | 1·05 |
| 50 | 42 | 2·09 |
| 50 | 41 | 3·14 |
| 50 | 40 | 4·19 |
| 50 | 39 | 5·23 |
| 50 | 38 | 6·1 |
| 50 | 37 | 6·98 |
| 50 | 36 | 7·85 |
| 50 | 35 | 8·72 |
| 49 | 42 | 1·06 |
| 49 | 41 | 2·12 |
| 49 | 40 | 3·18 |
| 49 | 39 | 4·25 |
| 49 | 38 | 5·13 |
| 49 | 37 | 6·01 |
| 49 | 36 | 6·9 |
| 49 | 35 | 7·78 |
| 49 | 34 | 8·67 |
| 48 | 41 | 1·08 |
| 48 | 40 | 2·15 |
| 48 | 39 | 3·23 |
| 48 | 38 | 4·13 |
| 48 | 37 | 5·02 |
| 48 | 36 | 5·92 |
| 48 | 35 | 6·82 |
| 48 | 34 | 7·72 |
| 48 | 33 | 8·61 |
| 47 | 40 | 1·09 |
| 47 | 39 | 2·18 |
| 47 | 38 | 3·09 |
| 47 | 37 | 4·0 |
| 47 | 36 | 4·91 |
| 47 | 35 | 5·83 |
| 47 | 34 | 6·74 |
| 47 | 33 | 7·65 |
| 47 | 32 | 8·56 |
| 46 | 39 | 1·11 |
| 46 | 38 | 2·03 |
| 46 | 37 | 2·96 |
| 46 | 36 | 3·88 |
| 46 | 35 | 4·8 |
| 46 | 34 | 5·73 |
| 46 | 33 | 6·65 |
| 46 | 32 | 7·57 |
| 46 | 31 | 8·5 |
| 45 | 38 | 0·94 |
| 45 | 37 | 1·87 |
| 45 | 36 | 2·81 |
| 45 | 35 | 3·75 |
| 45 | 34 | 4·69 |
| 45 | 33 | 5·62 |
| 45 | 32 | 6·56 |
| 45 | 31 | 7·5 |
| 45 | 30 | 8·25 |
| 44 | 37 | 0·95 |
| 44 | 36 | 1·9 |
| 44 | 35 | 2·85 |
| 44 | 34 | 3·80 |
| 44 | 33 | 4·75 |
| 44 | 32 | 5·70 |
| 44 | 31 | 6·65 |
| 44 | 30 | 7·41 |
| 44 | 29 | 8·16 |
| 43 | 36 | 0·96 |
| 43 | 35 | 1·92 |
| 43 | 34 | 2·88 |
| 43 | 33 | 3·77 |
| 43 | 32 | 4·81 |
| 43 | 31 | 5·77 |
| 43 | 30 | 6·54 |
| 43 | 29 | 7·31 |
| 43 | 28 | 8·08 |
| 42 | 35 | 0·97 |
| 42 | 34 | 1·95 |
| 42 | 33 | 2·92 |
| 42 | 32 | 3·9 |
| 42 | 31 | 4·87 |
| 42 | 30 | 5·65 |
| 42 | 29 | 6·43 |
| 42 | 28 | 7·21 |
| 42 | 27 | 7·99 |
| 41 | 34 | 0·99 |
| 41 | 33 | 1·97 |
| 41 | 32 | 2·96 |
| 41 | 31 | 3·95 |
| 41 | 30 | 4·74 |
| 41 | 29 | 5·52 |
| 41 | 28 | 6·32 |
| 41 | 27 | 7·11 |
| 41 | 26 | 7·89 |
| 40 | 33 | 1·0 |
| 40 | 32 | 2·0 |
| 40 | 31 | 3·0 |
| 40 | 30 | 3·8 |
| 40 | 29 | 4·6 |
| 40 | 28 | 5·4 |
| 40 | 27 | 6·2 |
| 40 | 26 | 7·0 |
| 40 | 25 | 7·8 |
| 39 | 32 | 1·01 |
| 39 | 31 | 2·03 |
| 39 | 30 | 2·84 |
| 39 | 29 | 3·65 |
| 39 | 28 | 4·46 |
| 39 | 27 | 5·27 |
| 39 | 26 | 6·08 |
| 39 | 25 | 6·89 |
| 39 | 24 | 7·7 |
| 38 | 31 | 1·03 |
| 38 | 30 | 1·85 |
| 38 | 29 | 2·67 |
| 38 | 28 | 3·49 |
| 38 | 27 | 4·32 |
| 38 | 26 | 5·14 |
| 38 | 25 | 5·96 |
| 38 | 24 | 6·78 |
| 38 | 23 | 7·60 |
| 37 | 30 | 0·83 |
| 37 | 29 | 1·67 |
| 37 | 28 | 2·5 |
| 37 | 27 | 3·33 |
| 37 | 26 | 4·17 |
| 37 | 25 | 5·0 |
| 37 | 24 | 5·83 |
| 37 | 23 | 6·67 |
| 37 | 22 | 7·5 |
| 36 | 29 | 0·84 |
| 36 | 28 | 1·69 |
| 36 | 27 | 2·53 |
| 36 | 26 | 3·37 |
| 36 | 25 | 4·21 |
| 36 | 24 | 5·06 |
| 36 | 23 | 5·9 |
| 36 | 22 | 6·74 |
| 36 | 21 | 7·58 |
| 35 | 28 | 0·85 |
| 35 | 27 | 1·7 |
| 35 | 26 | 2·56 |
| 35 | 25 | 3·41 |
| 35 | 24 | 4·26 |
| 35 | 23 | 5·11 |
| 35 | 22 | 5·97 |
| 35 | 21 | 6·82 |
| 35 | 20 | 7·67 |
| 34 | 27 | 0·86 |
| 34 | 26 | 1·72 |
| 34 | 25 | 2·59 |
| 34 | 24 | 3·45 |
| 34 | 23 | 4·31 |
| 34 | 22 | 5·17 |
| 34 | 21 | 6·03 |
| 34 | 20 | 6·9 |
| 34 | 19 | 7·76 |
| 33 | 26 | 0·87 |
| 33 | 25 | 1·74 |
| 33 | 24 | 2·62 |
| 33 | 23 | 3·49 |
| 33 | 22 | 4·36 |
| 33 | 21 | 5·23 |
| 33 | 20 | 6·1 |
| 33 | 19 | 6·98 |
| 33 | 18 | 7·85 |
| 32 | 25 | 0·88 |
| 32 | 24 | 1·76 |
| 32 | 23 | 2·65 |
| 32 | 22 | 3·53 |
| 32 | 21 | 4·41 |
| 32 | 20 | 5·29 |
| 32 | 19 | 6·18 |
| 32 | 18 | 7·06 |
| 31 | 24 | 0·89 |
| 31 | 23 | 1·79 |
| 31 | 22 | 2·68 |
| 31 | 21 | 3·57 |
| 31 | 20 | 4·46 |
| 31 | 19 | 5·36 |
| 31 | 18 | 6·25 |
| 30 | 23 | 0·9 |
| 30 | 22 | 1·81 |
| 30 | 21 | 2·71 |
| 30 | 20 | 3·61 |
| 30 | 19 | 4·52 |
| 30 | 18 | 5·42 |
| 29 | 22 | 0·91 |
| 29 | 21 | 1·83 |
| 29 | 20 | 2·74 |
| 29 | 19 | 3·66 |
| 29 | 18 | 4·57 |
| 28 | 21 | 0·93 |
| 28 | 20 | 1·85 |
| 28 | 19 | 2·78 |
| 28 | 18 | 3·7 |
| 27 | 20 | 0·94 |
| 27 | 19 | 1·87 |
| 27 | 18 | 2·81 |
| 26 | 19 | 0·95 |
| 26 | 18 | 1·9 |
| 25 | 18 | 0·96 |
+------+------+-------+
No further deduction shall be made when cloth is more than 15 inches
narrower than the reed space, or when cloth is narrower than 18 inches.
Fractions of an inch not to be recognized under this clause.
=5. Reeds.=--A 60 reed being taken as the standard, ¾ per cent. shall
be deducted for every two ends or counts of reed from 60 to 50, but
no deduction shall be made below 50. ¾ per cent. shall be added for
every two ends or counts of reed from 60 to 68, 1 per cent. from 68 to
100; 1½ per cent. from 100 to 110; and 2 per cent. from 110 to 132. All
additions or deductions under this clause to be added to or deducted
from the price of the standard 60 reed.
+--------------------+
| Deductions |
| from standard. |
+--------+-----------+
|Count of|Percentage.|
| reed. | |
+--------+-----------+
| 50 | 3¾ |
| 52 | 3 |
| 54 | 2¼ |
| 56 | 1½ |
| 58 | ¾ |
| 60 | standard |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
+--------+-----------+
+------------------------------------------+
| Additions to standard. |
| |
+--------+-----------+
|Count of|Percentage.|
| reed. | |
+--------+-----------+
| 62 | ¾ |
| 64 | 1½ |
| 66 | 2¼ |
| 68 | 3 |
| 70 | 4 |
| 72 | 5 |
| 74 | 6 |
| 76 | 7 |
| 78 | 8 |
| 80 | 9 |
| 82 | 10 |
| 84 | 11 |
| 86 | 12 |
| 88 | 13 |
| 90 | 14 |
| 92 | 15 |
| 94 | 16 |
| 96 | 17 |
| 98 | 18 |
| 100 | 19 |
| 102 | 20½ |
| 104 | 22 |
| 106 | 23½ |
| 108 | 25 |
| 110 | 26½ |
| 112 | 28½ |
| 114 | 30½ |
| 116 | 32½ |
| 118 | 34½ |
| 120 | 36½ |
| 122 | 38½ |
| 124 | 40½ |
| 126 | 42½ |
| 128 | 44½ |
| 130 | 46½ |
| 132 | 48½ |
+--------+-----------+
=6. Picks.=--_Low Picks._--An addition of 1 per cent. shall be
made for each pick or fraction of a pick below 11, thus:--
Below 11 to and including 10, 1 per cent.
„ 10 „ „ 9, 2 „
„ 9 „ „ 8, 3 „
„ 8 „ „ 7, 4 „
and so on, adding 1 per cent. for each pick or fraction of a pick.
_High Picks._--An addition of 1 per cent. shall be made for each pick
whenever they exceed the following:--
Weft below 26’s. when picks exceed 16
„ 26’s to 39’s inclusive „ „ „ 18
„ 40’s and above „ „ „ 20
In making additions for high picks, any fraction of a pick less than
the half shall not have any allowance; exactly the half-pick shall have
½ per cent. added; and any fraction over the half-pick shall have 1 per
cent. added.
=7. Twist.=--The standard being 28’s or finer, the following
additions shall be made when coarser twist is woven in the following
reeds:--
Below 28’s to 20’s in 64 to 67 reed inclusive, 1 per cent.
„ „ 68 „ 71 „ „ 2 „
„ „ 72 „ 75 „ „ 3 „
Below 20’s to 14’s in 56 „ 59 „ „ 1 „
„ „ 60 „ 63 „ „ 2 „
„ „ 64 „ 67 „ „ 3 „
and so on at the same rate.
When twist is woven in coarser reeds no addition shall be made.
=8. Weft.=--_Ordinary Pin Cops._--The standard being 31’s to
100’s, both inclusive, shall be reckoned equal. Above 100’s 1 per cent.
shall be added for every 10 hanks or fraction thereof.
In lower numbers than 31’s the following additions shall be made:--
For 30’s add 1 per cent.
„ 29’s, 28’s, add 2 per cent.
„ 27’s, 26’s, „ 3 „
„ 25’s, 24’s, „ 4½ „
„ 23’s, 22’s, „ 6½ „
„ 21’s, 20’s, „ 8 „
„ 19’s, 18’s, „ 10½ „
„ 17’s, 16’s, „ 13 „
„ 15’s, 14’s, „ 16 „
_Large Cops._--When weft of the following counts is spun into large
cops, so that there are not more than nineteen cops to the lb., the
following additions shall be made in place of the allowance provided
for pin cops in the preceding table:--
For 29’s, 28’s, add 1 per cent.
„ 27’s, 26’s, „ 2 „
„ 25’s, 24’s, 23’s, „ 3 „
„ 22’s, 21’s, 20’s, „ 4½ „
„ 19’s, 18’s, „ 6 „
„ 17’s, 16’s, „ 8 „
„ 15’s, 14’s, „ 10 „
=9. Four-stave Twills.=--_Low Picks._--In four-stave twills an
addition of 1 per cent. for each pick or fraction thereof below the
picks mentioned in the following table shall be made when using weft as
follows:--
Below 26’s, the addition shall begin at 13
26’s to 39’s, inclusive, „ „ „ 14
40’s and above, „ „ „ 15
_High Picks._--When using weft--
Below 26’s, the addition for high picks shall begin at 21
26’s to 39’s, inclusive, „ „ „ „ „ „ 22
40’s and above, „ „ „ „ „ „ 23
In making additions for high picks any fraction of a pick less than the
half shall not have any allowance; exactly the half-pick shall have ½
per cent. added, and any fraction over the half shall have the full 1
per cent. added.
=10. Splits.=--The following additions shall be made for splits:--
One split uncut, add 5 per cent.
Two splits „ „ 7½ „
Empty dents shall not be considered splits.
=11.= All the foregoing additions and deductions shall be made
separately.
This list is subject to a deduction of 10 per cent.
* * * * *
For fancy cloths the CHORLEY LIST, 1886, is the one most commonly used.
This is as follows:--
=Double-Lift Jacquards.=--To be paid the following over plain
cloth prices:--
For cloths with plain grounds, 30 per cent.
For cloths with satin grounds, 25 „
Brocades, damasks, and crammed stripes with three or more ends in a
dent, to be paid for by the number of ends per inch.
Picks 18 to 30 per quarter inch, 1 per cent. per pick; from 30 to 40
picks, ¾ per cent.; all above 40 picks, ½ per cent. instead of 1 per
cent.
Lace brocades, 5 per cent. extra.
Single-lift jacquards to be paid 10 per cent. about double-lift
machines.
The above applies to Jacquards only.
=Dobby and Tappet Looms (except Satins).=--To be paid the
following above plain cloth prices--
Up to and including--
4 staves 12 per cent.
5 „ 13 „
6 „ 14 „
7 „ 15 „
8 „ 16 „
9 „ 17 „
10 „ 18 „
11 „ 19 „
12 „ 20 „
13 „ 21 „
14 „ 22 „
15 „ 23 „
16 „ 24 „
17 „ 25 „
18 „ 26 „
19 „ 27 „
20 „ 28 „
Stripes and other cloths with three or more ends in a dent to be paid
for by the number of ends per inch.
In single-shuttle checks, handkerchiefs, and all special classes of
goods in which more than one pick is put in one shed, all lost picks
shall be counted.
Plain handkerchiefs, 72 reeds and below, to be paid 5 per cent. extra.
Single-shuttle cord checks with more than two picks in one shed to be
paid 2½ per cent. less.
Lace stripes and other special classes of goods shall be paid extra as
per special arrangement to be agreed upon by Employers’ and Operatives’
Associations.
The following example will show the method of calculating the price to
be paid for weaving under the Uniform List:--
_Example._--Find the weaving of a 44-inch cloth, 40 yards long,
woven in a loom 48-inch reed space, 92 reed, 30 picks per
quarter-inch, 40’s twist, 60’s weft.
2_d._ per pick standard
·09 = 4½ per cent. added for reed space
-----
2·09
·3135 = 15 per cent. added for reed
------
2·4035 = price per pick, 100 yards, with standard picks
30 picks
-------
72·1050 = price for 30 picks 100 yards
40 yards
----------
100)2884·2000
----------
28·84200 = price for 40 yards
2·884200 = 10 per cent. added for high picks
---------
31·726200 Total.
From this must be deducted 10 per cent., as per agreement, which will
give 28·5535 pence as the actual price to be paid for weaving this
piece of cloth.
The following example includes the allowance for narrow cloth woven in
broad looms:--
_Example._--Find the weaving price for 38-inch cloth woven in a
48-inch reed space loom, 50 reed, 507 dividend, 50 change wheel, 75
yards long, 32’s twist, 36’s weft.
2_d._ per pick standard
·09 = 4½ per cent. added for reed space
---
2·09
·078375 = 3·75 per cent. deducted for reed
--------
2·011625 = price per pick, 100 yards, 50 reed, 48-inch loom.
507
--- = 10·14 picks per quarter inch.
50
2·0116 × 10·14 picks × 75 yards
-------------------------------
100 yards
= 15·283218 price for 75 yards
·152832 = 1 per cent. added for pick
---------
15·436050
·637508 = 4·13 per cent. deducted for narrow cloth
---------
14·798542 = price per list
1·4798542 = 10 per cent. deduction
----------
13·3186878 = net price.
In making the additions and deductions it is important that they should
be made in the above order.
=The Cost of a Piece of Cloth.=--Besides the cost of material
and the weaving wage, the expenses of the manufacturer must be taken
into account. When a manufacturer makes only one kind of cloth, his
expenses will obviously not be so proportionately great as another
manufacturer’s who only takes a single order of a particular make. The
expenses also vary with the district and distance from the market, and
with other circumstances.
A manufacturer knows from experience exactly what amount of expenses to
allow in different classes of fabrics in his own case, and in quoting
prices for plain or fancy cloths he usually includes under the term
“expenses” all the items of cost from the carriage of the yarn to the
delivery of the cloth, including winding, warping, sizing, waste, and
other fixed expenses in the mill.
The expenses are usually calculated in proportion to the weaving wage,
and a manufacturer quotes “double weaving” or “three times weaving,”
according to the class of fabric in question.
The following example will illustrate the principle of estimating the
cost of a piece.
Find the cost of a piece, 34 inches full, 75 yards s.s. (short stick),
19 × 18, 32’s/40’s. Twist at 7_d._ per lb., weft at 7½_d._ per lb.
Weaving 2_s._ Expenses equal to weaving.
The 34-inch cloth would stand, say, 36 inches in the reed. The 75-yards
cloth, “short stick,” or 36 inches to the yard, will require, say, 78
yards of warp.
A cloth counting 19 × 18, nominal, is usually woven in a 68 or 70 reed,
and the picks per inch will be about 66 or 67 actually.
Assuming that the cloth stands 36 inches in a 70 reed, and the picks
per inch are 67, we get--
36 inches × 78 yards × 70 reed × 7_d._
------------------------------------- = 51.188_d._, cost of twist,
840 × 32’s
and
36 inches × 75 yards × 67 picks × 7½_d._
----------------------------------------- = 40.38_d._, cost of weft.
840 × 40’s
_d._
51.188 cost of twist
40.38 cost of weft
24.00 weaving wage
24.00 expenses
-------
139.568 cost of piece = 11_s._ 7½_d._
The amount allowed for expenses in the preceding example is perhaps
sufficient for most cloths woven on dobbies, but more is required for
jacquard-woven fabrics.
If 11_s._ 7½_d._ is quoted for the above cloth, the price is said to be
based on “double weaving.”
For jacquard fabrics the price is usually based on 2½ to 3 times
weaving, and in special cases, such as new styles, an extra profit is
put upon the 3-times weaving.
Sometimes the expenses are said to be 5 or 10 per cent. more than
weaving. If the weaving wage were 2_s._ 6_d._, and the expenses 10 per
cent. more than weaving, the expenses would be 2_s._ 9_d._
=Contraction.=--The length of warp required to weave a piece of
a given length will vary with the pattern or weave of the cloth, and
depends also on the elasticity of the yarn and the counts of both warp
and weft. Owing to this difference in the elasticity of various classes
of yarns, and the variation in the elasticity of the same yarn at
different degrees of tension, it is impossible to lay down rules for
the calculation of the exact warp length for a given length of piece,
or for the exact width in the reed for a required width of piece.
The length of warp required can only be obtained with exactness from
experience, especially in fancy cloths.
As previously stated, twofold yarns are more elastic than single;
indeed, with some kinds of twofold American yarns, such as are used in
velvets, the percentage of contraction becomes less with an increase in
the number of picks, owing to the increase of tension upon the yarn,
which causes it to stretch more.
Roughly, the amount of contraction to allow in the warp can be
obtained by taking into account the counts of weft and the number of
intersections which the warp makes with the weft. The thicker the
counts of weft the more the warp will be bent out of a straight line,
also with an increase in the number of picks the amount of take-up or
contraction will increase. This does not vary in a regular manner, as
the angle which the warp makes in bending over the weft changes with
any variation in the picks. Furthermore, the greater the tension on the
warp yarn the more it will stretch, and also the more it will compress
the weft at the point of intersection.
A rough estimate only can therefore be made if there is no previous
experience in the same class of goods to guide the manufacturer.
A method of roughly estimating the percentage of milling-up of the warp
is to multiply the intersections of the warp per inch by a number found
by experience to give the right result, and to divide this product by
the counts of weft used.
For rather heavily picked cloths the multiplier 4 gives a fairly
accurate result, and in cloths with a medium number of picks and medium
counts the multiplier 3 will be used. In some classes of goods the
multiplier requires to be 5; but when a correct multiplier is found
for a certain class of goods, it will serve for changes in that class.
The system is certainly not accurate in all cases, but it embraces
roughly the different causes which alter the percentage of contraction
or milling-up in the warp, and is therefore of some use in practice.
_Example._--Find the length of warp required to weave a piece of
5-stave satin 94 yards long (36 inches to the yard), 94 reed, 180
picks per inch, 60’s twist, 70’s weft.
The number of intersections per inch will be two-fifths of the
number of picks, as the warp intersects twice every five picks or
pattern.
∴180 × ⅖ = 72 intersections per inch;
and 72 × 4
----------- = 4 per cent. contraction.
70’s counts
The length of warp required to weave the 94 yards piece would
therefore, roughly, be 98 yards.
In a plain cloth the contraction is much more than in a satin, and the
percentage is greater in heavily picked cloths than light ones.
In a plain cloth of, say, 120 picks per inch, 60’s twist, 70’s weft,
the percentage of take-up will roughly be as follows:--
Intersections per inch = 120
4
---
70)480(6-6/7 per cent. contraction.
420
---
60
In a plain cloth the warp intersects every pick, and so the
intersections per inch are the same as the ends per inch. In a “two
and two” twill the warp intersects twice in four picks, and the
intersections per inch will be one-half the picks.
In more medium cloths the multiplier 3 is used; as, for example:--
Find percentage of contraction in a piece of plain cloth woven with 60
picks per inch, 32’s twist, 40’s weft.
60 × 3
----------- = 4½ per cent.
40’s counts
In fancy cloths experience is the only guide as to the warp length
required, but in striped cloths and similar fabrics woven from one beam
the contraction of the whole will be that of the tightest weave in the
pattern.
In a fabric in which there are only a _few_ plain ends in the pattern,
the other ends being loosely interwoven, it does not follow that the
take-up will be as much as in a plain cloth, as the plain ends will
compress the weft more at the point of intersection than could occur if
_all_ the ends were weaving plain.
=Testing Yarn.=--It often occurs that only a short length of yarn
is available for being weighted when it is required to test it for the
counts. If it is required to test the weft in a piece of grey cloth
it is usual to take out of the cloth 120 yards, or one “lea.” This
is one-seventh of a hank, and therefore if the weight of 120 yards
is divided into 1,000 grains--the one-seventh part of a pound--the
quotient will be the counts of the yarn. The reason of this will be
obvious when it is remembered that if the weight of one hank is divided
into 7000 grains, or 1 lb., the result is the number of hanks in 1 lb.,
or the counts.
The counts are based upon the number of hanks in 1 lb. avoirdupois,
and as this weight is not suitable for weighing small quantities, it
is necessary to weigh them in Troy weight. As nearly as possible 7000
grains Troy = 1 lb. avoirdupois.
_Example._--If 120 yards of cotton weft weighs 20 grains, what
counts is it?
1000
--------- = 50’s counts.
20 grains
If it is required to know the number of grains which 120 yards of
any count should weigh, the method of procedure is the reverse of the
foregoing.
_Example._--How many grains should 120 yards of 40’s yarn weigh?
1000 grains
----------- = 25 grains.
40’s counts
When testing the counts of cops, it is usual to wrap two, three, or
four cops, in order to arrive at a more satisfactory test.
If two leas, or two-sevenths of a hank, are weighed, the counts can be
obtained by dividing the weight into 2000 grains, or two-sevenths of 1
lb. If three leas, or 360 yards, are weighed, divide the weight into
3000 grains, and the result is the counts. If 480 yards are weighed,
the dividend is 4000; if 600 yards, or five leas, are weighed, the
dividend will be 5000; if six leas, or 720 yards, are weighed, the
dividend is 6000; and when seven leas, or one hank, is weighed, the
dividend will be 7000 grains, or 1 lb.
As it takes a considerable time to take 120 yards of weft out of
a piece, a shorter length is often weighed and the counts found
therefrom. A balance is extensively used which registers the counts
when twenty yards of yarn are put upon the pointer. This is a very
useful, though not always accurate, method.
When any odd length of yarn is weighed, the counts may be obtained by
proportion, thus--
If 34 yards of yarn have been found to weigh 8 grains, what count is it?
The yards in 1 lb. can first be found as follows:--
grains grains yards
8 : 7000 ∷ 34
34
-------
8)238000
-------
29750 yards in 1 lb.;
and this divided by 840 will give the counts, thus:--
29750
----- = 35·41 counts.
840
From this we get the formula:--
7000 × yards weighed
-------------------- = counts.
840 × counts
This is a very useful formula, as when only a small piece of cloth is
available to be tested it is necessary to get as near as possible to
the counts from weighing sometimes only 10 or 15 yards, or any odd
length.
A calculation may occur in the following form:--
How many grains should 16 yards of 20’s cotton weigh?
There are 840 × 20 = 16,800 yards of 20’s in 1 lb., or 7000 grains.
Then if 16,800 yards weigh 7000 grains, how many grains will 16 yards
weigh?
yards yards grains
16800 : 16 ∷ 7000 : 6·6 grains.
This may be stated in a formula as follows:--
7000 × yards weighed
-------------------- = weight in grains.
840 × counts
=Staub’s Yarn Balance= is a small balance which is made to test
the counts of very small quantities of yarn. A template is given with
the balance, and the yarn is cut into lengths the size of the template,
about two inches. One end of the balance is slightly heavier than the
other, and the number of threads the size of the template which are
required to draw the balance indicate the counts of the yarn. If twenty
threads or about 40 inches balance the small weight, the count of the
yarn is 20’s, and so on.
The principle is the same as if a 1 lb. weight were put on one end of a
balance, in which case the number of hanks required to draw the weight
would indicate the counts, because if 20 hanks = 1 lb. the counts are
20’s, and if 21 hanks = 1 lb. the counts are 21’s. The balance may be
made to weigh any length, according to the weight on one end of the
balance.
The form in which it is usually made makes it specially suitable for
testing the counts in small patterns of a few inches.
The test is, of course, only approximate, as could only be expected
from weighing so short a length.
If the foregoing examples are thoroughly understood, the following will
not be found difficult.
If a warp has 2000 ends, and is 500 yards long, and weighs 60 lbs.,
what counts is it?
The ends multiplied by the length will give the total length of yarn in
the warp, and this divided by 840 will give the hanks. If the hanks are
divided by the weight, the result will be the counts. The result may be
obtained at once as follows:--
2000 × 500
---------- = 19·84 counts.
840 × 60
If a beam has 2200 ends, the counts being 40’s, and the weight 50 lbs.,
find the length.
By multiplying 40 by 840 the yards in 1 lb. are obtained, and
multiplying this by 50, the yards of yarn on the beam are arrived at.
If this is divided by the ends in the warp, the result will be the
length of warp thus:--
40 × 840 × 50
------------- = 763·6 yards.
2200
A simple method of mentally calculating the number of hanks in a piece
is as follows:--
A warp 84 yards long will contain just one-tenth as many hanks as ends.
Thus a warp of 2000 ends, 84 yards long, contains 200 hanks. This can
be proved as follows:--
2000 × 84
--------- = 200 hanks.
840
The number of hanks in a warp 84 yards long can thus be seen at once,
and it is a very simple matter to mentally calculate the difference for
any other length.
The hanks of weft can also be calculated mentally in a similar manner.
If the piece is 84 yards, the counts multiplied by the width and
divided by 10 will give the number of hanks required for 84 yards.
Thus, find the hanks of weft in a piece 34 inches wide, 84 yards long,
60 picks per inch.
60 × 34
------- = 204 hanks.
10
The calculation is really simpler than it looks in the above form, as
the dividing by 10 can be done by simply pointing off the last figure
in the product of the picks and width. The formula may be proved
correct by working out fully as follows:--
34 × 84 × 60
------------ = 204 hanks.
840
This system of mentally calculating the hanks is very useful, as it
serves as a check upon a full calculation.
=The Firmness of Cloth.=--The number of ends and picks per inch which
can advantageously be put into a fabric depends upon the number of
intersections per inch in the pattern or weave, and on the counts or
diameters of the yarns used. In a plain cloth woven with 32’s twist and
32’s weft, the number of threads per inch which could be put into the
cloth without undue compression would be a little more than one-half
the number which could be laid side by side touching each other. The
reason for this is that the warp and weft threads interlace with each
other every pick, and therefore, supposing that 156 threads of 32’s
occupy one inch when laid side by side, one-half of these threads
would have to be left out to allow of the intersection of the weft
between every end.
In a “two and two” twill the weft intersects once for every two ends,
or twice in the pattern; therefore there are four threads and two
intersections in the pattern. It is obvious, therefore, that to keep
the same firmness in the twill as in the plain cloth with the same
yarns, a larger number of threads per inch both in warp and weft will
be required.
To keep the same “firmness” the threads must be kept as close together
in one cloth as in the other, and as in a plain cloth one-half the
threads which occupy one inch are dropped out, so in a twill with
two intersections for four ends there must be one-third of the ends
occupying one inch left out. Thus with 32’s yarn, of which the diameter
is 1/156 of an inch, there will require to be about 102 threads per
inch in a “two and two” twill.
A perfectly balanced plain cloth may be defined as a cloth in which the
warp and weft yarns are equal in diameter, and the spaces between the
threads are equal to the diameter of the yarn.
If the diameters of yarns of various counts are known, it is an easy
matter to find the number of threads per inch which will produce the
desired firmness in any simple weave.
The diameters of yarns of cotton, woollen, worsted, and other threads
are given by the late Mr. T. R. Ashenhurst in an excellent little work
on “Textile Calculations and the Structure of Fabrics,” which has done
much to promote this branch of the art of weaving.
Mr. Ashenhurst estimates the diameter of a 32’s cotton yarn at the
1/148th part of an inch; but this is probably somewhat under the mark,
and in the following table I have taken 1/156th inch as the diameter of
32’s.
The variation in the thickness of any yarn, and the fact that they are
not strictly cylindrical, renders measurements of little avail, but
taken in conjunction with an examination of a range of woven cloths,
the approximate or practical diameter can be estimated.
TABLE OF DIAMETERS OF COTTON YARNS.
+---------+---------+
| Counts. |Diameter.|
+---------+---------+
| 1 | 27½ |
| 2 | 39 |
| 3 | 47½ |
| 4 | 55½ |
| 5 | 62 |
| 6 | 67½ |
| 7 | 73 |
| 8 | 78 |
| 9 | 83½ |
| 10 | 87½ |
| 11 | 91 |
| 12 | 95 |
| 13 | 99 |
| 14 | 103 |
| 15 | 106½ |
| 16 | 110 |
| 17 | 113 |
| 18 | 117 |
| 19 | 120 |
| 20 | 123½ |
| 21 | 126 |
| 22 | 129½ |
| 23 | 132 |
| 24 | 135 |
| 25 | 138 |
| 26 | 140½ |
| 28 | 145½ |
| 30 | 151 |
| 32 | 156 |
| 34 | 160½ |
| 36 | 165 |
| 38 | 169 |
| 40 | 174½ |
| 42 | 178 |
| 44 | 183 |
| 46 | 187 |
| 48 | 191 |
| 50 | 195 |
| 52 | 198½ |
| 54 | 202½ |
| 56 | 206 |
| 58 | 210 |
| 60 | 213 |
| 62 | 216½ |
| 64 | 220½ |
| 66 | 224 |
| 68 | 227 |
| 70 | 230½ |
| 72 | 233½ |
| 74 | 237 |
| 76 | 240½ |
| 78 | 243 |
| 80 | 246 |
| 82 | 249 |
| 84 | 252 |
| 86 | 256½ |
| 88 | 258½ |
| 90 | 261 |
| 92 | 264 |
| 94 | 267 |
| 96 | 270 |
| 98 | 272½ |
| 100 | 275½ |
| 105 | 282 |
| 110 | 289 |
| 115 | 295½ |
| 120 | 302 |
| 125 | 308 |
| 130 | 314 |
| 135 | 320 |
| 140 | 326 |
| 145 | 331½ |
| 150 | 337 |
| 160 | 349 |
| 170 | 359 |
| 180 | 369 |
| 190 | 380 |
| 200 | 390 |
+---------+---------+
The preceding is a table of the diameters of cotton yarns from 1’s
counts to 200’s. The number given as the diameter is the number of
threads which occupy the space of one inch when laid as close together
as possible without compression.
A perfectly balanced plain cloth will require one-half this number
of threads per inch, plus, perhaps, 5 per cent. for the threads being
forced somewhat out of the same plane in weaving.
=Relative Diameters of Yarns.=--The “counts” of yarns indicate
the number of hanks in 1 lb., and therefore a given length of 30’s is
twice as heavy as the same length of 60’s; but the diameter of the 30’s
will not be twice that of the 60’s, as the yarns are cylindrical, and
the diameters will vary as the square roots of the areas, which in this
case are as 1: 2.
If one thread is four times as heavy as another, and if it is of the
same _density_--which in these calculations is assumed, although it is
not strictly correct--the diameters of the two threads will be as 2: 1.
For example, looking at the tables, the diameter of a 60’s is seen to
be the 1/213 of an inch, whilst the diameter of a thread four times the
weight, viz. 15’s, is seen to be 1/106½ of an inch, or exactly twice
the diameter of the 60’s thread.
The diameter of one yarn being known, the diameter of any other may be
obtained by the following rule:--
RULE.--As the square root of one count is to the square root
of another count, so is the diameter of one to the diameter of the
other.
_Example._--If the diameter of a 16’s yarn is the 1/110th part of
an inch, find the diameter of a 36’s.
√(16) : √(36) ∷ 110
4 : 6 ∷ 110 : 165 _Ans._
In this form the calculation necessitates the extraction of two square
roots, and with most numbers would require the use of two fractions in
the calculation. By squaring all the three terms the calculation is
much simpler, as in the following example:--
_Example._--If the diameter of a 32’s is the 1/156 of an inch, what
is the diameter of a 50’s?
32’s : 50’s ∷ 156^2 : _x_^2
or 32 : 50 ∷ 24336 : _x_^2
50
-------
32)1216800(38025
96
---
256
256
------
80
64
----
160
160
and √38025 = 195 _Ans._
As the diameters of yarns vary as the square root of their counts, it
follows that the diameters will always bear a certain relation to the
yards in 1 lb. If this relation is once obtained, it becomes easy to
calculate the diameter of any yarn on this principle.
Taking the diameter of a 32’s yarn from the table, viz. 156, it will be
found that this is equal to the square root of the yards in 1 lb., less
5 per cent.
_Example._ 840
32
----
1680
2520
-----
26880 yds. in 1 lb. of 32’s.
√26880 = 164
8 = 5 per cent.
---
156 = diameter of 32’s.
The number of ends and picks per inch required to make plain cloths of
equal firmness from different counts may be at once seen from the table
of diameters, as one-half the number given as the diameter is required.
Thus if a plain cloth with 78 threads per inch of 32’s is taken as the
standard, and it is required to make a cloth of equal firmness, with
60’s yarns, the number of threads per inch required would be 106½. In
20’s yarns about 62 threads would be required. In 16’s yarns 55 threads
per inch, and so on.
In twills, or other regular weaves, the following rule will give the
number of threads per inch required of any count:--
RULE.--As the sum of the ends and intersections in the pattern
is to the ends, so is the diameter to the number of threads required.
_Example 1._--How many threads per inch are required to make a
perfectly balanced “2 and 1” twill cloth, with 24 yarns, warp and
weft?
There are 3 ends and 2 intersections in the pattern; therefore
3 ends + 2 intersections = 5;
and as 5 : 3 ends ∷ 135 diameter : _x_
3
---
5)405
----
81 threads per inch required.
_Example 2._--How many threads per inch are required to make a
perfectly balanced “3 up, 2 down, 2 up, 2 down twill” with 44’s
yarns?
In this pattern there are 9 ends and 4 intersections; therefore
as 9 + 4 : 9 ∷ 183 diameter of 44’s : _x_
or, as 13 : 9 ∷ 183
9
----
13)1647(126 threads per inch required
13
---
34
26
---
87
78
--
9
One of the most useful purposes to which a knowledge of this principle
can be put is in changing the weave of a fabric, to find the threads
per inch of a given count of yarn required to keep the same firmness as
in a sample cloth.
It must be remembered that the word “firmness” is here used as implying
that the space between the threads bears the same relation to the
diameters of the threads in both cases, or, if the given cloth is
perfect, the proposed one will also be perfect.
Suppose it is desired to make a “two and two” twill of the same
“firmness” as a plain cloth made with 103 threads per inch.
The yarns being the same, the number of threads per inch required will
be as the ends plus intersections in a given number of ends in both
patterns.
In the above question the given cloth is plain, with 103 threads per
inch, and the proposed cloth is a “two and two” twill. Taking the same
number of threads in each case, we get--
Ends + Intersections in Ends + Intersections
proposed twill cloth. in given plain cloth.
4 + 2 : 4 + 4 ∷ 103 : _x_
or 6 : 8 ∷ 103
8
----
6)824
----
Ends required in twill cloth = 137⅓
It must not be forgotten that it is necessary to take an equal number
of ends of each pattern in this class of calculation. In more complex
patterns it is often advisable to take the number of ends which is
the L.C.M. of the ends in the two patterns in order to get a
complete number of intersections in each case.
_Another Example._--If a “two and two” twill cloth is made with 137
threads per inch, and it is proposed to make a cloth with the same
counts of yarns in a “5 up, 2 down, 1 up, 2 down” twill, how many
threads per inch are required to keep the same firmness?
In 40 ends of the proposed cloth there are 16 intersections, and in
40 ends of the sample cloth there are 20 intersections.
Then as 40 + 16 : 40 + 20 ∷ 137
or 56 : 60 ∷ 137
60
----
56)8220(146.8 threads. _Ans._
56
262
224
----
380
336
----
440
If it is required to make a cloth with the same number of threads as a
sample cloth, and to change the pattern and keep the same firmness, it
is necessary to change the counts on the following principle:--
RULE.--As the sum of the ends and intersections in the sample
cloth is to the sum of the ends and intersections in the proposed
cloth, so is the square root of the counts in the sample to the square
root of the counts in the proposed cloth.
_Example._--If a plain cloth has been made with 36’s yarns, and
it is proposed to make a “two and two” twill with the same number
of threads per inch, find the counts required to keep the same
“firmness.”
Ends + Inters. Ends + Inters.
in sample cloth. in proposed cloth.
or 4 + 4 : 4 + 2 ∷ √36 : √x
8 : 6 ∷ 6 :
6
--
8)36
4½
And 4½^2 = 20·25 counts required.
This may be proved correct by referring to the table of diameters on
page 335, where it will be seen that a plain cloth with 82½ threads per
inch of 36’s is “perfect,” and a “two and two” twill with 82½ threads
of 20¼’s counts is equally perfect.
=To change the Counts=, the pattern and threads per inch remaining
the same.
If a sample cloth has 78 threads per inch of 32’s yarn, and it is
proposed to make a cloth of the same weave with 55 threads per inch,
what counts of yarn are required to keep the same “firmness”?
This is simple enough. The diameters of yarns vary as the square root
of their counts, and therefore as the threads in one cloth are to the
threads in another, so will the square root of the counts in one be to
the square root of the counts in the other.
Threads in Threads in proposed Counts in
sample. cloth. sample.
78 : 55 ∷ √32 : √x
or as 78^2 : 55^2 ∷ 32
6084 : 3025 ∷ 32
32
----
6050
9075
-----
6084 )96800(15·91, or 16’s nearly = counts
6084 required
-----
35960
On referring to the table of diameters (p. 335), it will be found that
a plain cloth with 78 threads of 32’s is “perfect,” and that a plain
cloth with 55 threads of 16’s is also perfect. Therefore the above
calculation is correct.
=To change the Threads per Inch=, the counts and pattern remaining
the same.
If a sample has 78 threads per inch of 32’s, and it is proposed to
weave a cloth of the same pattern, but with 60’s yarns, find the number
of threads per inch required to keep the same firmness.
This is simply a continuation of the previous statement.
If the two counts are known, the number of threads will vary as the
square roots of the counts; thus--
Counts in Counts in Threads in
sample. proposed cloth. sample.
√32 : √60 ∷ 78 : _x_
or as 32 : 60 ∷ 78^2 : _x_^2
6084
60
-------
32)365040
11407½
√11407 = 106.8 threads required.
The above may be proved correct by referring to the table of diameters.
A plain cloth with 78 threads per inch of 32’s is “perfect,” and so is
a plain cloth with 106½ threads per inch of 60’s.
The same principle must be employed if the warp and weft are of
different counts, or if the threads per inch are not equal in warp and
weft.
_Example._--A sample cloth is made with 78 ends per inch of 32’s
and 91 picks per inch of 44’s. How many picks will be required to
keep the same firmness, if the weft only is changed to 60’s?
Counts in Counts in
sample. proposed cloth.
√44 : √60 ∷ 91 : _x_
or as 44 : 60 ∷ 91^2 : _x_^2
8281
60
------
44)496860
------
11292 = _x_^2
------
and √11292 = 106½ ∴ picks per inch required = 106½
One advantage gained by a knowledge of the principle of cloth
“balance” is that the number of picks per inch which a given pattern
or weave will take can easily be obtained by calculation. This is of
great advantage to designers for Jacquard weaving, as it often occurs
that a design is made and the cards cut for a pattern which will not
admit of the required number of picks of the given counts being put in
the cloth, which a slight alteration in the ground weave would have
rendered possible.
=To alter the Weight.=--If the weight of a cloth is required to be
altered, and the same firmness kept, the threads per inch and counts
can be found on the same principle.
If a cloth is made heavier it must be done by using _coarser_ yarns and
_fewer_ threads; it cannot be done by using more threads, and preserve
the same “firmness” or “perfection.”
Suppose a sample piece of cloth weighing 10 lbs. is made with 93
threads of 45’s, and it is proposed to make a piece of the same length
and width, but weighing 15 lbs. To find the threads per inch and counts
of yarn to keep the same firmness.
The weights of two cloths will vary as the square roots of the counts
if they are of the same perfection.
Therefore--
Weight of Weight
proposed cloth. of sample.
As 15 lbs. : 10 lbs. ∷ √45 : √(_x_) counts
or 15^2 : 10^2 ∷ 45 to _x_
225 : 100 ∷ 45
100
----
225)4500(20’s counts required
450
----
0
To find the threads per inch required of the above counts--
Weight of Weight of
proposed cloth. sample.
15 : 10 ∷ 93
10
----
15)930(62 threads required.
90
----
30
30
----
Then to make a piece of the same perfection or firmness as the sample
piece, and to alter the weight from 10 lbs. to 15 lbs., the counts must
be changed from 45’s to 20’s, and the threads per inch from 93 to 62.
To prove this is correct take a piece 20 inches wide, 102 yards long,
93 threads per inch both in warp and weft of 45’s yarns.
The weight of this sample piece will be--
20 × 102 × 93
------------- = 5 lbs. of twist;
840 × 45
and as there is the same weight of weft, the total weight of the piece
will be 10 lbs.
Now calculate the weight of a piece of the same length and width with
62 threads per inch of 20’s yarns:--
20 × 102 × 62
------------- = 7½ lbs. of twist;
840 × 20
and with the same quantity of weft, the total weight of the piece will
be 15 lbs.
This proves the calculation to be correct so far as altering the weight
goes.
To see if both cloths are of the same firmness, the table of diameters
may be referred to. It will there be seen that a plain cloth with 93
threads per inch of 45’s yarn is “perfect,” and also that the altered
cloth with 62 threads of 20’s is equally perfect.
It thus proves the principle of the calculation to be correct.
A lighter cloth may be made, and the same firmness kept. The formula is
the same in both cases. If a cloth is made lighter it must be done by
using finer counts and more threads. It cannot be done by using fewer
threads, as the firmness could not be kept and the required weight
obtained.
In altering the weights of cloths some allowance would have to be
made for the difference in milling-up with different counts of yarns
and numbers of threads. If a cloth is made heavier, thicker yarns
would be used, and the warp length to give a certain length of piece
would be different in the sample to the altered cloth. But this is
a comparatively small matter, which can be adjusted with a slight
alteration in the basis of the structure.
INDEX
Antiseptics, 32
Automatic looms, 198
Backed cloths, with weft, 255;
with warp, 257
Barley-corn patterns, 235
Beaming, press, 47
---- tension, 47
Beating up the weft, 72, 85
----, character of motion in, 72, 73
----, distance moved by slay whilst the crank moves through given
angle in, 74
----, eccentricity of slay’s movement in, 72;
cause of, 74
----, effect of altering position of crank-shaft in, 83;
of reversing direction of crank in, 84
----, force of slay in, 78, 82
----, position of crank in, 72
Becks, size mixing, 30
Brake, 95
Calculation for two or more fold yarns, 308
---- of contraction for different weaves and counts, 326
---- of cost of a piece, 325
---- of counts of yarn from weighing given length, 329
Calculation of diameter of yarn, 336
Calculation of number of threads of given counts required to make a
firm cloth in any weave, 341
---- of quantity of warp and weft in a piece, 311-313
---- of reeds and setts, 310
---- of weaving wage, 324
---- of weight of a given length of any counts, 330
---- to make a cloth of equal firmness to given cloth when changing
weave, 338
---- to preserve firmness and alter weight, 343
---- to preserve firmness when changing threads per inch, 341
---- to preserve same firmness when changing counts, 341
Card-cutting machine, 190
---- repeater, 191
Casting out, 285
Checks produced by re-arranging twills, 241
Circular-box motion, 115
Clearer guide, 8
Clipped or sheared cloths, 254
Coiling motions. _See_ Taking-up
Combined twills, 226
Cop winding machine, 6
Cording plan for hand loom, 50
Cords, 245
Corkscrew twills, 257
Counts of cotton yarns, 307
Counts of two or more unequal threads twisted together, 308;
and weight of each required in given weight of resulting
thread, 309
Cover on cloth, 86, 87
Crapes, 248
Crimp cloth, 249
Damask or twilling Jacquards, 168-172
Design, transferring from sketch to point paper, 281
Detached figures, spots, arrangement of, 278-281
Development of pattern, 282-285
Diagonals, fancy, produced by combining unequal twills, 240
---- figured, 289
Diameters of cotton yarns, 335
Diapers, 233
Dice checks, 234
Direction of twist in yarns, effect of, 304
Dobbies, timing of movements in, 129
---- undermotions for, 130, 131
Dobby, the Blackburn, 127;
knife motion for, 127;
character of shed in, 129
----, the Keighley double-lift, 123;
method of pegging for, 126;
double jacks in, 126;
character of shed in, 125;
made positive, 129
Double cloths, 259
---- bound by passing back pick over face end, 261
---- bound by passing back end over face pick, 262
---- plain clothes, figuring, 263;
bound together, 266
---- shed Jacquard, 157
---- twill cloth figuring, 300
---- warp face, 257
Double weft face, 255
Double-beat slay, 135
Doup heald, 173
Draft, arranging on point paper, 227
---- the V, 230; patterns produced by, 230-233
Drawing-in, 3
Drills, 224
Drop-box motion, Diggle’s, 107
---- in pick-and-pick loom, 116;
connected to Jacquard, 120
---- Whitesmith’s, 112
---- Wright Shaw’s, 109
Drum winding machine, 13, 14
Edleston harness, 166
---- ---- designing for, 294
Extra warp, figuring with, 250;
reeding of, 252
---- ---- and extra weft combined, 255
---- weft, figuring with, 252
---- figure on mock leno ground, 254
Fancy effects produced by warp and weft pulling each other out of
straight line, 249
Fast reeds, 91
Figured design, 278
---- leno designing, 295
Firmness of cloth, 333
Gauze, plan of, 173
“Gloy,” 33
Grey warps, preparation of, 2
Hand-loom, 48
Hattersley weft-replenishing device, 214
Heck of warping mill, 22
Honeycomb designs, 242
Huck patterns, 250
Jacquard card cutting, 142, 190
---- damask or twilling, 168-172
---- damask, Tschorner and Wein, 172
---- double-shed, 157
---- for cross-border, 155
---- for leno weaving, 181
---- harness, bordered pattern, Norwich tie, 151;
London tie, 153
---- centre pattern or point tie, 154
---- Edleston’s, 166;
designing for,167, 294
---- for all-over pattern, 139
---- London tie, 150
---- Norwich tie, 144, 150
---- machine, origin of, 137
---- sizes of, 150
---- difference in character of shed between single and
double-lift, 137, 144-148
---- double-lift, single-cylinder, 144;
principle of, 145
---- double-lift, double-cylinder, 146;
advantages of, 144
---- single-lift, 138
---- open-shed, 158
---- pressure harness, 161-166
---- split harness, 160
Jeans, jeanettes, 220
Keighley dobby, 123
Kenyon’s undermotion for dobbies, 131
Lace and leno stripes, 269
Lags, pegging of, 126
Lappet loom, 193
---- wheel, construction of, 195
Lappets, 192
Leno checks, 268
---- crossovers, 175
Leno effects, 266
---- full cross, 181
---- Jacquards, designing for, 185
---- double-lift, 186
----, imitation of, 186
---- net or lace, 176
---- selvedge, 132
---- weaving in dobbies, 174-180;
use of slackener in, 174;
arrangement of staves and pegging plan, 175-178;
shaking motion for double-lift dobbies, 178;
arrangement of slackeners for two doups, 180
Letting-off, 106
Linen yarns, counts of, 307
List of prices for weaving, New Uniform, 314-322;
Chorley, 322
Loose reeds, 92
Marking mechanism in slashing frame, 35
Marseilles quilts, 298
Mildew, 32
Mitcheline, 299
Mock lenos, 243
Mono-coloured warps, preparation of, 3
Multi-coloured warps, preparation of, 5
Net lenos, 267
Northrop weft-replenishing device, 210
Oscillating tappets, 61
Padded cloths, 258
Patterns produced by combining alternate picks of twills, 240
---- by combining equal twills, 226;
unequal twills, 240
---- by drafting, 227
Patterns by fancy drafts, 238
---- by re-arrangement of simple twills, 236;
and of combined twills, 237
Pegging plan making, 228
Pick-and-pick loom, 116
Pick, force of, 69
Picking, over pick, 68, 69
---- under pick, 71
Pile fabrics, warp, 189
---- weft, 270-277
Piqués, 258
Pirn winding machine, 15
---- ---- ---- disc, 17
Plain cloth, 218
---- draft for weaving, 219
---- number of threads possible in, 218
---- ornamentation of, 218
Plushes, 189, 275
Point draft, 230
Point paper, selection of, for different proportions of warp and
weft, 290
---- use of, 219
Power-loom, tappet shedding motions in, 51-68
Preparatory processes, 1
Presser roller, expanding, 27
Pressure harness, designing for, 292
---- harnesses, 161-166
Primary movements in weaving, 48
---- timing of, 85-87
Protector, loose reed, 91
---- stop rod, 92
Reeds and setts, 310
Ribs and cords, 245
Roller top motion for plain cloth, 62;
3 staves, 64;
4 staves, 64;
5 staves, 65;
7 staves, 66
Sack weaving, 259
Satin draft, 229
---- weaves, 222
Satin, principle of construction of, 224
Scotch dressing, 42
Section blocks, expanding, 27
---- tappets, Woodcroft’s, 59, 60
Sectional warping, 23
Selvedge motion in sateen loom, 134, 135
Set figures, arrangement of, 278-281
Shading, 283
Shedding motions, power-loom, 51-68
Silk yarns, thrown or net, numbering of, 307
Sines and cosines, table of, 81
Singleton’s stop-motion, 19
Size mixing, 28
---- ---- for light sizing, 30
---- ---- for fine counts, 31
---- ---- for medium sizing, 31
---- ---- for heavy sizing, 32
Sizes of patterns woven in Jacquards, 285
Sizing, 28
---- ball, 43
---- materials, 28
----, slashing frame, 33;
slow motion in, 37
---- frame, slasher, marking motion in, 35, 36
---- ---- frictional winding motion in, 39
---- machines, hot air drying in, 38
---- ----, automatic supply of size to, 40
Slubbings, 8
Solid coloured borders in dhooties, 303
Split harness, designing for, 292
Splits, motion for, 132
---- Shorrock and Taylor’s motion for, 133
Spreading the warp, 85
Spun silk yarns, counts of, 307
Stitching-thread used to bind extra warp and extra weft, 252, 253
Stocks and bowls, 67
Stop motion, weft fork, 93
---- ----, in beam-warper, 19
---- rod, 92
Striped designs, 288;
calculation of reed for, 288
Tabby weave, 218
Taking-up motion, negative, 101;
screw and worm wheel, 103
---- positive, 95;
Pickles’, 99;
new system, 104
Tappets, calculation for lift of, 52
----, construction of, 53
----, effect of treadle-bowl on, 57
---- for plain cloth, 50, 51, 53
---- for twills, 56, 58
---- oscillating, 61
---- positive, 59
----, speed of, 87-91
---- Woodcroft’s, 59
Terry cloth, 187
---- loom, 187
Testing yarns, 329
Three-ply, four-ply cloths, 263
Toiletings, 297
Traverse motions, heart cam, 9, 10;
mangle wheel, 11 cloths, 258
Trial section, 25
Twaddell’s hydrometer, 30
Twills, 219
---- combined, 226
Twisting-in, 3
Twofold yarns, cotton, worsted, silk, 308
Undermotions, 130, 131
Undermotion, Kenyon’s, 131
V-creel, 18, 23
V-reed, 24
Velvet, common, 270
---- cords, 276
---- E1, 273
---- fast pile, 273
----, figured, 301
---- twill back, 274
Velvets, velveteens, 270, 277;
definition of, 272
Warp line, 85
Warping, beam, 18
Warping mill, 21
----, sectional, 23
Weaving wage calculations, 324
Weft, preparation of, 6
----, wet, 6
---- fork, 93
---- pile fabrics, 270
Weft-replenishing devices, automatic, 198-217
---- ----, patents for, 209
---- ----, Northrop, 210
---- ----, Hattersley, 214
Winding coloured yarn, 14
---- drum, 14
---- from cops to warpers’ bobbins, 6
---- from ring spools to warpers’ bobbins, 6
---- from throstle to warpers’ bobbins, 6
Woodcroft’s section tappets, 59, 60
Worsted yarns, 307
Wrapping yarn, 330
Yarn balance, Staub’s, 331
---- twist of, 305
Yorkshire dressing, 5, 47
THE END
PRINTED BY
WILLIAM CLOWES AND SONS, LIMITED
LONDON AND BECCLES
End of Project Gutenberg's Cotton Weaving and Designing, by John T. Taylor