_Of the Division of the Water for the respective Worts
and Mashes, and of the Heat adequate to each of these._
That the whole quantity of water, as well as that of heat required,
ought not, in any brewing, at once to be applied to the grist, is
obvious, both from reason, and from the example of nature, who, in
forming the juice of the grape, divides the process, and increasing
successively both the moisture and the heat, gives time to each degree
to have its complete effect. A division of the water and heat to form
malt liquors is equally necessary, but previous to this division the
following general rules may be laid down.
The grist, if possible, is at no time to be left with less water than
what will cover the malt, to put all its parts in action. In the first
mashes for strong beer, an allowance is to be made for nearly as much
water as the grist will imbibe; and, lastly, the whole quantity of
water used in brewing should be divided, in a proportion analogous to
that of the degrees of heat.
Processes for brewing are carried on either with one copper or with
two. Though the first of these methods is almost out of use, it may be
necessary to give an example or two of the division of the water used
in this case, the doing which will point out the absurdity of this
practice.
In brewing with one copper, scarcely more than three mashes can be
made; otherwise the time taken up in boiling the worts, and preparing
the subsequent waters for extraction, would be so long, as to cause the
grist to lose great part of its heat, and, in warm weather, perhaps, to
become sour. The whole water required might naturally be divided into
three equal parts, was it not for the quantity at first imbibed by the
grist; but as, in this way of brewing, the best management is to make
the first wort of one mash, and the second wort of the other two, it
will be found necessary to allow, for the first extracting water, four
parts out of seven of the whole quantity required, and to divide the
remainder equally for the other two mashes. Thus, if the whole quantity
of water required was fifty-one barrels, the lengths of the extracting
waters would be as follow:
1 Liquor 2 Liquor 3 Liquor.
29---------11-------------11 Barrels.
1 Wort. ╰━━━━v━━━━╯
2 Wort.
The water imbibed and retained by the malt is allowed for in this
computation, which will be found just to every purpose, for small beer
brewed in one copper only.
But in strong beers and ales, with three mashes, whether brewed at
one, two, or three worts, the case will be somewhat different, as
care should always be taken to reserve for every mash a sufficient
quantity of water to apply to the grist. For this reason, no greater
proportion ought to be used in the first mash than that of three parts
out of seven, as the volume of the malt is in a greater proportion to
the quantity of water than in the preceding case. If, therefore, the
whole quantity of water used was thirty-five barrels, the length of the
liquors would be:
1 Liquor 2 Liquor 3 Liquor.
15 10 10 Barrels.
Employing only one copper, must from hence appear, and is allowed to
be, bad management; for, in some part or other of the process, however
well contrived, the business must stand still, and consequently the
extracts be injured, by the air continually affecting them. The best
and most usual practice, and that which here will be set in example, is
to brew with two coppers. Other rules consequently are necessary to be
observed, and I shall be more particular in the explanation of them.
To preserve order, and to convey our ideas in the clearest manner, we
shall make use of the four modes of brewing we mentioned, in the fourth
section.
The first of these, which implies keeping pale strong and keeping
pale small beers to become spontaneously fine, are best brewed with
two worts and four mashes, to allow for what is imbibed by the grist,
and what is steamed away during the first part of the process, four
sevenths of the whole of the water employed, and consequently a like
proportion of the number of the degrees which constitute the difference
between the first and last heats of the whole brewing, are required for
the first wort, and the remainder to the last or second. The proportion
as to the water is permanent, but having now only a division of heat in
a progressive state, for the temperature to be given to the extracts,
to put in practice the principles laid down in pages 64, 65; the first
wort, however, composed of several mashes, must be of one uniform
heat, though less than that of the second, whose extracts, though more
powerful, must, notwithstanding, be of equal heat among themselves.
According to the rules laid down in section 8, the whole quantity of
water requisite for a guile of keeping pale strong, or keeping pale
small beer, is fifty-one barrels. In page 171, we found, including the
heat lost at the time the extract separates from the grist, the first
heat to form this process to be 144 degrees, and the last 158 degrees;
the quantity of water, and the difference between these two degrees,
are required to be divided in such proportions as are best applicable
to the purpose we intend.
Water 51 Barrels, multiplied by
4
----
Divided by 7) 204
----
Gives 29 Barrels for the first Wort, and
this deducted from 51,
Leaves 22 Barrels for the second Wort.
The twenty-nine barrels, equally divided between the two first mashes,
is fourteen barrels and a half for each; and the twenty-two barrels,
equally divided between the two last mashes, is eleven barrels for each.
The last heat for pale keeping beers is 160 degrees.
And the first is 146 degrees.
----
Their difference is 14
This, as above, multiplied by 4
----
And divided by 7) 56
----
Leaves 8 degrees.
the proportion to be allotted to the first wort, and 6 degrees, the
remainder, to the last, in a regular progressive state; the elements
for this brewing would stand as under.
Malt’s Value of Whole First Second Third Fourth
dryness. hops. medium. mash. mash. mash. mash.
Degrees 119 3 138 146 154 157 160
Barrels 14-1/2 14-1/2 11 11
But more exactly, to imitate the fermented liquors formed by nature,
our first wort, answering to the germinating part of her process must
be of one uniform heat in the extracts, as must likewise our second
wort: (See page 165) the mean, then, of the progressive heats of the
first wort will be that which must be applied both to the first and
second mashes, and the mean of the progressive heats of the second
wort, that which must direct the third and fourth mashes; from whence
are deduced
_Elements for forming keeping pale strong and keeping pale small beers._
Malt’s Value of Whole First Second Third Fourth
dryness. hops. medium. mash. mash. mash. mash.
Degrees 119 3 138 150 150 158-1/2 158-1/2
Barrels 14-1/2 14-1/2 11 11
First wort. Second wort.
That this method of applying the heats to the mashes corresponds to the
medium heat which is to govern the whole process, the circumstances
required in page 165, the following operation will prove.
29 Barrels, the first wort.
Heated to 150
----
1450
29
----
4350
----
22 Barrels, the second wort.
Heated to 158-1/2
------
11
176
110
22
------
Whole 3487
quantity 4350
of water, ------
Barrels 51 )7837( 153 The mean heat of the 4 mashes.
51 2 Deducted for the heat lost at the
---- ---- tap.
273 151 Heat of the tap’s spending.
255 119 Malt’s dryness.
---- ----
187 270
153 ----
---- 135 Mean heat of Malt’s dryness and of the extracts.
3 Value of hops.
----
138 Mean heat of the whole process.
----
Admitting of the necessary variations in the medium heats which are to
govern processes for different purposes, and of those in the number
of degrees forming the constituent parts of the must, in proportion as
the drinks are to be formed, either to become spontaneously fine, or
made so by precipitation, or intended for a longer or shorter duration.
This rule will be found universally true, when beers are brewed with
two worts: but when, for the benefit of the drink, or on account of
the smallness of the utensils, as is often the case, when the second
mode of extraction is put in practice, we are obliged to carry on
the process with three worts, these proportions must necessarily
be altered, and the following have, in this case, been found most
advantageous.
The first and second wort ought to have two thirds of the water; the
first wort two thirds of this quantity, the second the remainder of
this, and the third wort one third part of the whole.
Porter or brown beer is the sort of drink, in which this division is
most commonly observed. Let the whole quantity of water to be used be
that of the brewing, of which the elements have been laid down, (page
233) or 54 barrels.
54
2
----
3) 108
----
36
2
----
3) 72
----
24 Barrels of water for the first wort.
12 Barrels for the second wort.
18 Barrels for the third wort.
----
54
----
The last degree
for this drink is,
with malt dried
to 130 degrees, 165 Degrees.
The first, as per
page 178 155 Degrees.
----
Their difference 10 Degrees.
2
----
3) 20
----
7
2
----
3) 14
----
5 Heat of first wort.
Five degrees to be proportioned in the first wort, and these deducted
from 7 degrees, the number allowed for the first and second wort,
there remains two degrees for the second wort; and seven degrees
deducted from ten, the whole difference, leaves three degrees, to be
proportioned in the third and last wort.
A grist of eleven quarters of malt is too large, to admit of the water
allowed for the first wort to be equally divided between the first and
second mash; therefore, rather than use the whole 24 barrels in one
mash, a sufficient quantity only must be applied to the first mash,
both to work it, and to get as much of the extract to come down, as
will save the bottom of the copper it is to be pumped into. By this
management, there will be enough left to form the second extract with,
or what by the brewers is termed the piece liquor. The exact quantity
of water the first mash should have, might be referred to the following
section, but the order we have laid down, will excuse our anticipating
thereon.
It has been found, and will hereafter be proved, that a volume of
eleven quarters of malt, dried to 130 degrees, is equal to 6,32 barrels
of liquid measure, that malt in general requires twice its volume of
water to wet it, and this quantity of water is retained after every tap
is spent.
6,32 Barrels, volume of the 11 quarters of malt.
3
------
18,96
6,32
------
12,64 Barrels of water imbibed by the grist,
which, deducted from
24,00 Whole quantity of water allowed for
the first wort.
------
Remains 3) 11,36 Extract, which will be yielded from
the first and second mash.
3,78 Length of the first piece, which is
sufficient to save the copper.
------
3,78
12,64 Quantity imbibed as above.
------
16,42 Quantity of water for the first mash.
7,58 Quantity of water for the second mash.
------
24,00
The elements of this brewing, as we have them (page 178) placed in
a progressive state, will be as under, where the quantity of water
allowed for the first wort is divided into two mashes, according to
the circumstances just now taken notice of, where the second wort is
formed by one entire mash, and the water allotted for the third wort is
separated equally into two parts, for the two last mashes, and when the
ten degrees of heat, the difference between the first and last heats
employed, are as near as possible proportioned to the lengths of the
worts.
Malt’s Value Whole First Second Third Fourth Fifth
dryness. of hops. medium. mash. mash. mash. mash. mash.
Deg. 130 4 148 155 160 162 164 165
Barrels 16 8 12 9 9
But, for the reasons alleged in page 236, they admit of the following
variation.
_Elements for brewing brown beer or porter._
Malt’s Value Whole First Second Third Fourth Fifth dryness. of hops.
medium. mash. mash. mash. mash. mash.
Deg. 130 4 148 157-1/2 157-1/2 162 164 165
Barrels 16 8 12 9 9]
╰━━v━━╯ ╰━v━╯ ╰━━v━━╯
1 wort 2 wort 3 wort.
And, if proved as before, the same correspondence will be found with
the medium governing heat.
The third mode of extraction is intended for a drink which is soon
to be ready for use, in which, in the coldest season of the year,
transparency is expected, and, in the hottest months, soundness:
to procure these intents, we have already shewn (page 191) it was
necessary to vary the medium heats governing these several processes,
in proportion as the seasons of the year differed as to heat and cold.
Our present business is a proper division of the whole quantity of
water necessary for brewing, into the respective worts and mashes,
and to apply to each, the adequate degree of heat: one single example
will suffice for the operation, and the whole variety this drink is
subjected to, will be expressed in the table subjoined.
The general practice to brew common small beer, and which is best,
is to form it with two worts and four mashes, and, in this case,
as was before practised for keeping pale beers, in order to allow
for the water at first absorbed by the grist; four sevenths of the
whole quantity is required for the first wort, and the remainder for
the second wort, dividing these quantities again into equal parts,
for their respective mashes. As a speedy spontaneous pellucidity is
expected in every season of the year, and as every means for producing
this without affecting the soundness of the drink, must be put in
practice, the whole number of constituent parts are not only applied,
but likewise the progressive heats suffered to take place: for here,
through necessity, we are compelled to forsake the rules nature
pointed out, (as in pages 64, 65); the reasons why are obvious; this
drink receives no benefit by the slow progress nature recommends, and
therefore very little by the impressions of time.
In page 232, we found the whole quantity of water to be used for the
brewing there specified, fifty-one barrels, and in page 191, we find
when the heat of the air is at 60, the first heat is 154, the last 174
degrees.
Water 51 Barrels, multiplied by
4
----
Divided by 7) 204
----
Gives 29 for the first Wort, and this deducted
from 51,
Leaves 22 for the second Wort.
The twenty-nine barrels, divided into the first and second mashes, will
be fourteen barrels and a half for each; and the twenty-two barrels,
equally divided between the third and fourth mashes, is eleven barrels
each.
The last heat for this brewing of common small beer
is (see page 191) 174 degrees.
The first heat, 154 degrees.
----
Their difference 20
Multiplied by 4
----
And divided by 7) 80
----
Leaves (to avoid fractions) nearly 12 degrees,
to be proportioned in the first wort, and 8 degrees, the remainder
of the 20, to the second wort, in a regular progressive state: the
elements for this brewing are:
Malt’s Value of Whole First Second Third Fourth
dryness. hops. medium. mash. mash. mash. mash.
Degrees 130 2 148 154 166 170 174
Barrels 14-1/2 14-1/2 11 11
╰━━━v━━━╯ ╰━━v━━╯
First wort. Second wort.
The quantity of water used for brewing small beer is in proportion to
the largeness of the grist, and the price of the grain; this admitting
of almost an endless variety, it is needless to pursue it: but the
dryness of the malt, the value of the hops, the medium governing the
processes, and the heat of the extracts being fixed, and constant
degrees of heat in proportion to that of the air, I have constructed
the following table, which will be found useful to the practitioner in
every season of the year.
Heat of Malt’s Value of Whole First Second Third Fourth
air. dryness. hops. medium. mash. mash. mash. mash.
35 122 1 135 138 150 154 158
40 124 1 137 140 152 156 160
45 125 1 140 145 157 161 165
50 127 1 143 149 161 165 169
55 129 1-1/2 146 152 164 168 172
60 130 2 148 154 166 170 174
The last business of this section is to divide the quantity of water
requisite to brew pale ales or amber, and to apply to such divisions
their necessary degrees of heat. This liquor is rather an effort
of art, than an exact imitation of nature, as in it the greatest
transparency, joined to the greatest strength, is expected in a very
short time. To obtain these ends, the whole number of the constituent
properties of malt and two mashes only are employed. In the first, in
order to favor its pellucidity, the lowest adequate extracting degree
must be used; and in the second, to cause the malt to yield the whole
of its necessary parts, the highest fitting heat must be applied; the
whole of the process is, nevertheless, subjected to the governing
medium heat of 138 degrees, the highest which admits of voluntary
brightness. But where a drink is formed with two mashes only, and
boiled off in one entire wort, to keep the due proportion between the
quantity of water used, and the heat required in the extracts, and
at the same time to allot the proper quantity for what is imbibed by
the grist, the most convenient division found, will be three-fifths
of the whole quantity of water to be applied to the first mash, and
the remaining two-fifths to the other. I know to this, custom may be
objected, that the first mash for amber should be a stiff one, in
order the better to retain the heat; but this, in the division here
proposed, may equally be obtained by a proper allowance made in the
attemperating of the water, without affecting the proportion of the
heats required, as otherwise must be the case.
From 8 quarters of malt to make 13 barrels of fine ale.
13 Length.
1/2 Boiling half hour.
12-1/2 Waste water.
------
26 Whole water employed, multiplied by
3
------
Divided by 5) 78
Gives 16 Barrels for the first mash, and leaves
10 Barrels for the second mash,
the lowest heat being required in the first extract, and the highest in
the last, according to page 194; for the 16 barrels it will be 144, and
for the 10 barrels it will contain 164 degrees.
But as the heat of the air occasions a difference in the quantities of
hops to be used, and as from hence the extracts are somewhat varied: it
has been judged convenient to add the following table:
A TABLE _of the elements for forming pale ale or amber,
at every degree of heat in the air, with the allowance of
two degrees of heat, in the first and last extractions_.
Heat of Malt’s Value of Medium heat of the extracts, First Last
air. dryness. hops. and of malt’s dryness. heat. heat.
35 120 1/2 138 147 167
40 120 3/4 138 146 167
45 120 1 138 146 166
50 120 1-1/2 138 145 165
55 120 1-1/2 138 145 165
60 120 2 138 144 164
In summer time, it is sometimes thought better to brew this drink with
malts more dried; for conveniency sake, I here insert two examples.
Heat of Malt’s Value of Whole Heat of Heat of
air. dryness. hops. Medium. first mash. last mash.
60 122 2 138 142 162
60 124 2 138 140 160
For the management of small beer made after amber, see page 197.
Thus having shewn how to ascertain the quantities of the malt, the
hops, the water, and the heat to be used, and to proportion them to
each other, as the good or bad properties of beers arise from the
extracts, and fire is the governing agent, we must now seek the
means to administer the right portion of heat, and so to temper the
water that is to form the extracts, as not to be disappointed of our
intentions. In the calculations made for this purpose, not only the
water in the copper, but the value and effect of the grist, as to heat
and cold, must be considered.