TREATMENT AND USE OF METALS
ANNEALING.--A very important part of the novice's education is a
knowledge pertaining to the annealing of metals. Unlike the artisan in
wood, who works the materials as he finds them, the machinist can, and,
in fact, with many of the substances, must prepare them so they can be
handled or cut by the tools.
Annealing is one of the steps necessary with all cutting tools, and it
is an absolute requirement with many metals for ordinary use, as well as
for many other articles like glass. This is particularly true in the use
of copper.
TOUGHNESS AND ELASTICITY.--It means the putting of metals in such a
condition that they will not only be less brittle, but also tougher and
more elastic. Many substances, like glass, must be annealed before they
can be put in condition for use, as this material when first turned out
is so brittle that the slightest touch will shatter it, so that it must
be toughened.
Malleable or wrought iron, if subjected to pressure, becomes brittle,
and it is necessary to anneal it. Otherwise, if used, for instance, for
boiler plates, from the rolled sheets, it would stand but little
pressure.
The most immediate use the boy will have is the treatment of steel. He
must learn the necessity of this process, and that of tempering, in all
his cutting tools, and in the making of machinery where some parts are
required to be constructed of very hard metal.
THE PROCESS.--To anneal steel it must be heated to a bright cherry red
and then gradually cooled down. For this purpose a bed of fine charcoal,
or iron filings and lime, is prepared, in which the article is embedded,
and permitted to remain until it is cold.
There are many ways of doing the work, particularly in the use of
substances which will the most readily give up their carbon to the tool.
Yellow prussiate of potash is an excellent medium, and this is sprinkled
over the cherry-heated article to be annealed. The process may be
repeated several times.
TEMPERING.--This is the reverse of annealing as understood in the art.
The word itself does not mean to "harden," but to put into some
intermediate state. For instance, "tempered clay" means a clay which has
been softened so it can be readily worked.
On the other hand, a tempered steel tool is put into a condition where
it is hardened, but this hardness is also accompanied by another
quality, namely, _toughness_. For this reason, the word _temper_, and
not _hardness_, is referred to. A lathe tool, if merely hardened, would
be useless for that purpose.
TEMPERING CONTRASTED WITH ANNEALING.--It will be observed that in
annealing three things are necessary: First, heating to a certain
temperature; second, cooling slowly; third, the particular manner of
cooling it.
In tempering, on the other hand, three things are also necessary:
First: The heating temperature should be a dull red, which is less than
the annealing heat.
Second: Instead of cooling slowly the article tempered is dipped into a
liquid which suddenly chills it.
Third: The materials used vary, but if the article is plunged into an
unguent made of mercury and bacon fat, it will impart a high degree of
toughness and elasticity.
MATERIALS USED.--Various oils, fats and rosins are also used, and some
acids in water are also valuable for this purpose. Care should be taken
to have sufficient amount of liquid in the bath so as not to evaporate
it or heat it up too much when it receives the heated body.
Different parts of certain articles require varying degrees of hardness,
like the tangs of files. The cutting body of the file must be extremely
hard, and rather brittle than tough. If the tang should be of the same
hardness it would readily break.
_Gradual Tempering._--To prevent this, some substance like soap suds may
be used to cool down the tang, so that toughness without hardness is
imparted.
The tempering, or hardening, like the annealing process, may be repeated
several times in succession, and at each successive heating the article
is put at a higher temperature.
If any part of a body, as, for instance, a hammerhead, should require
hardening, it may be plunged into the liquid for a short distance only,
and this will harden the pole or peon while leaving the other part of
the head soft, or annealed.
Glycerine is a good tempering substance, and to this may be added a
small amount of sulphate of potash.
FLUXING.--The word _flux_ means to fuse or to melt, or to put into a
liquid state. The office of a flux is to facilitate the fusion of
metals. But fluxes do two things. They not only aid the conversion of
the metal into a fluid state, but also serve as a means for facilitating
the unity of several metals which make up the alloy, and aid in uniting
the parts of metals to be joined in the welding of parts.
UNITING METALS.--Metals are united in three ways, where heat is used:
First: By heating two or more of them to such a high temperature that
they melt and form a compound, or an alloy, as it is called.
Second: By heating up the points to be joined, and then lapping the
pieces and hammering the parts. This is called forge work or welding.
Third: By not heating the adjacent parts and using an easily fusible
metal, which is heated up and run between the two, by means of a
soldering iron.
The foreign material used in the first is called a flux; in the second
it is termed a welding compound; and in the third it is known as a
soldering acid, or soldering fluid.
The boy is not so much interested in the first process, from the
standpoint of actual work, but it is necessary that he should have some
understanding of it.
It may be said, as to fluxes, generally, that they are intended to
promote the fusion of the liquefying metals, and the elements used are
the alkalis, such as borax, tartar, limestone, or fluor spar.
These substances act as reducing or oxidizing agents. The most important
are carbonate of soda, potash, and cyanide of potassium. Limestone is
used as the flux in iron-smelting.
WELDING COMPOUNDS.--Elsewhere formulas are given of the compounds most
desirable to use. It is obvious that the application of these substances
on the heated surfaces, is not only to facilitate the heating, but to
prepare the articles in such a manner that they will more readily adhere
to each other.
OXIDATION.--Oxidation is the thing to guard against in welding. The
moment a piece of metal, heated to whiteness, is exposed, the air coats
it with a film which is called an _oxide_. To remove this the welding
compound is applied.
The next office of the substance thus applied, is to serve as a medium
for keeping the welding parts in a liquid condition as long as possible,
and thus facilitate the unity of the joined elements.
When the hammer beats the heated metals an additional increment of heat
is imparted to the weld, due to the forcing together of the molecules of
the iron, so that these two agencies, namely, the compound and the
mechanical friction, act together to unite the particles of the metal.
SOLDERING.--Here another principle is involved, namely, the use of an
intermediate material between two parts which are to be united. The
surfaces to be brought together must be thoroughly cleaned, using such
agents as will prevent the formation of oxides.
The parts to be united may be of the same, or of different materials,
and it is in this particular that the workman must be able to make a
choice of the solder most available, and whether hard or soft.
SOFT SOLDER.--A soft solder is usually employed where lead, tin, or
alloys of lead, tin and bismuth are to be soldered. These solders are
all fusible at a low temperature, and they do not, as a result, have
great strength.
Bismuth is a metal which lowers the fusing point of any alloy of which
it forms a part, while lead makes the solder less fusible.
HARD SOLDER.--These are so distinguished because they require a
temperature above the low red to fuse them. The metals which are alloyed
for this purpose are copper, silver, brass, zinc and tin. Various alloys
are thus made which require a high temperature to flux properly, and
these are the ones to use in joining steel to steel, the parts to be
united requiring an intense furnace heat.
SPELTER.--The alloy used for this purpose is termed "spelter," and
brass, zinc and tin are its usual components. The hard solders are used
for uniting brass, bronze, copper, and iron.
Whether soft or hard solder is used, it is obvious that it must melt at
a lower temperature than the parts which are to be joined together.
There is one peculiarity with respect to alloys: They melt at a lower
temperature than either of the metals forming the alloys.
SOLDERING ACID.--Before beginning the work of soldering, the parts must
be cleaned by filing or sandpapering, and coated with an acid which
neutralizes the oxygen of the air.
This is usually muriatic acid, of which use, say, one quart and into
this drop small pieces of zinc. This will effervesce during the time the
acid is dissolving the zinc. When the boiling motion ceases, the liquid
may be strained, or the dark pieces removed.
The next step is to dissolve two ounces of sal ammoniac in a third of a
pint of water, and in another vessel dissolve an ounce of chloride of
tin.
Then mix the three solutions, and this can be placed in a bottle, or
earthen jar or vessel, and it will keep indefinitely.
THE SOLDERING IRON.--A large iron is always better than a small one,
particularly for the reason that it will retain its heat better. This
should always be kept tinned, which can be done by heating and plunging
it into the soldering solution, and the solder will then adhere to the
iron and cover the point, so that when the actual soldering takes place
the solder will not creep away from the tool.
By a little care and attention to these details, the work of uniting
metals will be a pleasure. It is so often the case, however, that the
apparatus for doing this work is neglected in a shop; the acid is
allowed to become dirty and full or foreign matter, and the different
parts separated.